Lightolier Work Light ISC3MR User Manual

INSTRUCTION SHEET NO.  
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE  
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.  
To assure full compliance with local codes and regulations, check with your local electrical inspector before  
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.  
IS: C3MR  
Retain these instructions for maintenance reference.  
Page 1 of 2  
B0206  
INSTALLATION PROCEDURE FOR CALCULITE® EVOLUTION TRIMS  
WARNING: USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURER’S  
REFLECTOR TRIMS MAY VOID THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.  
1. MAKE SURE THAT POWER TO THE LUMINAIRE IS OFF.  
2. Select proper LAMP for application.  
Fig. 1  
3. Remove TRIM FACEPLATE from TRIM BODY by  
compressing TORSION SPRING. Fig. 1  
Trim Body  
4. Insert LAMP between LAMP SPRINGS of LAMP HOLDER  
ASSEMBLY until face of LAMP sits firmly on GLASS LAMP  
Torsion Spring  
GUARD. Fig. 2  
Trim Faceplate  
CAUTION! RISK OF FIRE. GLASS LAMP GUARD MUST BE  
INSTALLED. Lamp manufacturers require the glass  
lampguard be in place before energizing lamp, and that  
great care must be taken that lamp is fully cooled before re-  
lamping. Avoid finger marks on the inside of the lamp, as it  
may shorten lamp life or cause breakage.  
Lamp  
Fig. 2  
5. Insert LAMP HOLDER ASSEMBLY into TRIM BODY until  
LAMP SPRINGS snap into place. Fig. 3  
6. Bring TRIM BODY to FRAME and attach SOCKET to bi-pin  
prongs on LAMP ensuring LAMPHOLDER ASSEMBLY remains  
in place. Fig. 3  
Lamp Springs  
Lamp Holder  
Assembly  
Lamp Removal  
Spring  
Prior to installing your LIGHTOLIER TRIM, the horizontal rotation  
can be preset within the luminaire. Note the BEAM CENTERING  
NOTCH Fig.4 allows the installer to predetermine the direction  
the lamp will point to illuminate a wall or object of interest (not  
applicable to downlight trims). Once the notch is aligned with the  
object of interest, simply tighten the ROTATIONAL BRAKE  
SCREW until the spring is fully compressed Fig. 5.  
Fig. 3  
Socket  
7. Ensure the two SECURING CLIPS are in the disengaged  
position.Fig.1 on pg. 2. Align the two THICK CEILING READY  
BRACKETS with the SECURING CLIPS and insert TRIM BODY  
up until the bottom of TRIM BODY is flush or slightly recessed  
from bottom of ceiling plane. Properly engage SECURING  
CLIPS by pushing them into THICK CEILING READY  
BRACKETS. Fig’s 2 & 3 on pg. 2  
Thick Ceiling  
Ready Brackets  
Rotational  
Fig. 5  
Brake Screw  
Beam  
Centering  
Notch  
Fig. 4  
U.S. AND FOREIGN PATENTS PENDING  
A
COMPANY  
631 Airport Road, Fall River, MA 02720  
 

LG Electronics Air Conditioner L6004 1 User Manual
LightSpeed Technologies Stereo System CAT 860 User Manual
Linn Stereo Amplifier EXOTIK PRE AMPLIFIER User Manual
Maxim Kitchen Utensil MAXEK2 User Manual
Maytag Dishwasher W10185072A User Manual
McCulloch Lawn Mower M155B107HK User Manual
Melissa Bread Maker 643 043 User Manual
Melissa Microwave Oven 653 116 User Manual
Metra Electronics Automobile Accessories 95 2009 User Manual
Microsoft Computer Accessories QLF 00195 User Manual