Pelco Security Camera C1303M B 5 05 User Manual

I N S T A L L A T I O N  
ExSite Series  
Explosionproof  
Camera Module  
®
C1303M-B (5/05)  
 
Important Safety Instructions  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.  
6. To reduce the risk of ignition of hazardous atmospheres, disconnect the equipment from the supply circuit before opening. Keep assembly  
tightly closed when in operation.  
7. The maximum ambient temperature range is -76°F to 140°F (-60°C to 60°C).  
8. Only use attachments/accessories specified by the manufacturer.  
9. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use  
caution when moving the cart/apparatus combination to avoid injury from tip-over.  
10. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-  
supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or  
moisture, does not operate normally, or has been dropped.  
11. Installation should be done only by qualified personnel and conform to all local codes.  
12. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not  
be installed where exposed to rain and moisture.  
13. Use only installation methods and materials capable of supporting four times the maximum specified load.  
14. Use stainless steel hardware to fasten the mount to outdoor surfaces.  
15. AN ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorporated in the electrical installation of  
the building.  
16. A readily accessible disconnect device shall be incorporated in the building installation wiring.  
17. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform  
any servicing other that contained in the operating instructions unless you are qualified to do so.  
18. Only use replacement parts recommended by Pelco.  
The product and/or manual may bear the following marks:  
This symbol indicates that dangerous voltage constituting a risk of electric shock is present  
within this unit.  
CAUTION:  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
This symbol indicates that there are important operating and maintenance instructions in the  
literature accompanying this unit.  
WARNING: HAZARDOUS MOVING PARTS. KEEP FINGERS AND OTHER BODY PARTS AWAY.  
WARNING: To reduce the risk of ignition of hazardous atmospheres, disconnect the  
equipment from the supply circuit before opening. Keep assembly tightly closed when  
operating.  
WARNING: To reduce the risk of ignition of hazardous atmospheres, conduit runs must have  
a sealing fitting connected within 2 inches of the enclosure.  
TO REDUCE THE RISK OF IGNITION, DO NOT OPEN WHEN AN EXPLOSIVE GAS ATMOSPHERE  
MAY BE PRESENT.  
C1303M-B (5/05)  
3
 
Getting Started  
Thank you for purchasing Pelco’s ExSiteSeries explosionproof integrated positioning system. This manual includes instructions for installing the  
camera module for the ExSite Series system. For complete system installation instructions, refer to the installation manual placed in the pan and  
tilt box.  
WARNING: Do not connect the power module to a supply circuit unless all ExSite system components (pan and tilt, camera module, and  
power module) are installed.  
Once the complete system is installed, refer to the operation/programming manual shipped with the camera module for instructions on how to  
operate and program your system.  
4
C1303M-B (5/05)  
 
Installation  
To install the camera module do the following:  
SET SCREW  
Figure 1. Loosen Setscrew  
continue to loosen it until it can be removed.  
WARNING: To avoid thread damage, carefully remove the back of the enclosure. Never use force to remove the back of the camera  
enclosure.  
CAMERA  
ENCLOSURE  
BACK  
SPANNER  
WRENCH  
Figure 2. Remove Back Cap of Enclosure  
C1303M-B (5/05)  
5
 
   
camera’s power connector to the mating connector located inside the enclosure.  
Only models with wipers: The tab located inside the enclosure must be pointing down before installing the camera module (refer to  
Figure 3). To position the tab, place the wiper located at the front of the enclosure in the center of the viewing window (refer to Figure 4).  
WARNING: Do not force the camera module into the enclosure.  
TAB  
CENTER  
NOTCHES  
CAMERA  
MODULE  
CAMERA  
ENCLOSURE  
Figure 3. Install Camera Module  
CENTER WIPER  
Figure 4. Center Wiper  
6
C1303M-B (5/05)  
 
   
a. Place the supplied green bushing on the stud located behind the handle of the camera module. The bushing should be in the same  
b. Install the wiper arm. Place the ridge of the arm in the notch of the enclosure tab and the slot of the arm over the green bushing.  
SET TAB IN  
CENTER POSITION  
8-32 PHILLIPS FLAT  
HEAD SCREW  
ARM  
CAMERA  
MODULE  
HANDLE  
STUD  
BUSHING  
Figure 5. Install Wiper Arm  
WARNINGS:  
To avoid thread damage, carefully install the back cap to the enclosure.  
Never force the back cap onto the end of the enclosure.  
When installation is completed, there should be no gap between the back cap and the enclosure.  
6. Reinstall the back cap on the enclosure by doing the following:  
a. Use your hands and turn the back cap clockwise until you can no longer turn it with your hands. The back cap should turn easily until  
it comes in contact with the O-ring. If it does not turn easily, the threads are not aligned and thread damage will occur.  
b. Continue tightening the back cap with the supplied spanner wrench. There should be no gap between the back cap and the enclosure  
when the back cap is tightened and properly installed.  
c. Once the back cap is installed, secure the back cap with the set screw using the supplied 1.5 mm Allen wrench.  
C1303M-B (5/05)  
7
 
 
Maintenance  
CAMERA MODULE REPLACEMENT  
The ExSite camera module can be replaced only with a camera module with the same model number. If a different camera model is installed in  
an existing system, the system will not function and a message to contact the Pelco factory will appear on the screen.  
DANGER: To reduce the risk of ignition of hazardous atmospheres, disconnect the equipment from the power supply before opening.  
Keep assembly tightly closed when operating.  
To replace the camera module do the following:  
a. Loosen the set screw with a 1.5 mm Allen wrench.  
b. Use the supplied spanner wrench to loosen the back cap of the camera enclosure. Once the back is loose, use your hands to continue  
to loosen it until it can be removed.  
CAMERA  
ENCLOSURE  
BACK  
SET SCREW  
SPANNER  
WRENCH  
Figure 6. Remove Back Cap of Camera Enclosure  
2. Remove the 8-32 Phillips flat head screw that secures the camera module inside the enclosure, refer to Figure 7.  
SET TAB IN  
CENTER POSITION  
8-32 PHILLIPS FLAT  
HEAD SCREW  
ARM  
CAMERA  
MODULE  
HANDLE  
STUD  
BUSHING  
Figure 7. Remove or Install Camera Module  
8
C1303M-B (5/05)  
 
 
3. For models with wipers, also remove the wiper arm and the green bushing from the unit (see Figure 7).  
4. Slide the camera module out of the enclosure.  
WARNING: Never force the camera module into the enclosure.  
5. Install the new camera module by doing the following:  
camera’s power connector to the mating connector located inside the enclosure.  
Only models with wipers: The tab located inside the enclosure must be pointing down before installing the camera module (refer to  
Figure 8). To position the tab, place the wiper located at the front of the enclosure in the center of the viewing window (refer to Figure 9).  
TAB  
CENTER  
NOTCHES  
CAMERA  
MODULE  
CAMERA  
ENCLOSURE  
Figure 8. Install Camera Module  
CENTER WIPER  
Figure 9. Center Wiper  
C1303M-B (5/05)  
9
 
   
6. Refer to Figure 7 and do the following to reinstall the arm of the wiper:  
a. Reinstall the green bushing on the stud located behind the handle of the camera module.  
b. Reinstall the wiper arm. Place the ridge of the arm in the notch of enclosure tab and the slot of the arm over the green bushing.  
7. Secure the camera module and the wiper arm with the 8-32 Phillips flat head screw (refer to Figure 7).  
WARNINGS:  
To avoid thread damage, carefully install the back cap to the enclosure.  
Never force the back cap onto the end of the enclosure.  
When installation is completed, there should be no gap between the back cap and the enclosure.  
8. Reinstall the back cap on the enclosure by doing the following:  
a. Use your hands and turn the back cap clockwise until you can no longer turn it with your hands. The back cap should turn easily until  
it comes in contact with the O-ring. If it does not turn easily, the threads are not aligned and thread damage will occur.  
b. Continue tightening the back cap with the supplied spanner wrench. There should be no gap between the back cap and the enclosure  
when the back cap is tightened and properly installed.  
c. Once the back cap is installed, secure the back cap with the set screw using a 1.5 mm Allen wrench.  
10  
C1303M-B (5/05)  
 
Specifications  
Camera  
Day/Night (23X) Color  
NTSC, PAL  
LowLight(22X) Color  
NTSC, PAL  
Signal Format  
Scanning System  
Image Sensor  
2:1 interlace  
2:1 Interlace  
1/4-inch EXview HADCCD  
1/4-inch CCD  
Effective pixels  
NTSC  
PAL  
724 (H) x 494 (V)  
724 (H) x 582 (V)  
768 (H) x 494 (V)  
752 (H) x 582 (V)  
Horizontal Resolution  
NTSC  
PAL  
>470 TV lines  
>470 TV lines  
>470 TV lines  
>460 TV lines  
Lens  
F1.6 (f = 3.6~82.8 mm optical)  
23X optical, 10X digital  
F1.6 (f = 4~88 mm optical)  
22X optical, 12X digital  
Zoom  
Zoom Speed  
Horizontal  
Angle of view  
Focus  
2.9/4.2/5.8 seconds  
2.4/3.9/6.3 seconds  
54° at 3.6 mm wide zoom  
2.5° at 82.8 mm telephoto zoom  
Automatic with manual override  
47° at 4.0 mm wide zoom  
2.2° at 88 mm telephoto zoom  
Automatic with manual override  
Maximum Sensitivity  
at 35 IRE  
NTSC  
0.08 lux at 1/2 sec shutter (color)  
0.3 lux at 1/60 sec shutter (B-W)  
0.013 lux at 1/2 sec shutter (B-W)  
0.08 lux at 1/1.5 sec shutter (color)  
0.3 lux at 1/50 sec shutter (B-W)  
0.013 lux at 1/1.5 sec shutter (B-W)  
0.02 lux at 1/2 sec shutter  
0.02 lux at 1/1.5 sec shutter  
PAL  
Sync System  
Internal/AC line lock, phase adjustable via  
remote control, V-Sync*  
Internal/AC line lock, phase adjustable via remote  
control, V-Sync*  
White Balance  
Automatic with manual override*  
Automatic with manual override*  
Shutter Speed  
NTSC  
Automatic (electronic iris)/Manual  
1/2~1/30,000*  
Automatic (electronic iris)/Manual  
1/2~1/30,000*  
PAL  
1/1.5~1/30,000*  
1/1.5~1/30,000*  
Iris Control  
Automatic Iris Control with manual override*  
Automatic Iris Control with manual override*  
Gain Control  
Automatic/OFF*  
1 Vp-p, 75 ohms  
>50 dB  
Automatic/OFF*  
1 Vp-p, 75 ohms  
>50 dB  
Video Output  
Video Signal to Noise  
*Manual control of camera setup functions can be done with CM6700, CM6800, CM8500, CM9500, CM9740, CM9760, CM9770,  
CM9780, KBD200A, KBD300A, and MPT9500 controllers, but not with CM7500, MPT9000, or KBD9000 controllers.  
REVISION HISTORY  
Manual #  
C1303M  
C1303M-A  
C1303M-B  
Date  
11/04  
2/05  
Comments  
Original version.  
Added maintenance section for camera module replacement.  
Revised instructions for models with wipers.  
5/05  
Pelco and the Pelco logo are registered trademarks of Pelco.  
ExSite and LowLight are trademarks of Pelco.  
©Copyright 2005, Pelco. All rights reserved.  
EXview HAD is a trademark of Sony Corporation.  
C1303M-B (5/05)  
11  
 
Worldwide Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East  
|
|
|
|
|
|
|
|
 

Perreaux Stereo Amplifier E160 User Manual
Philips Cell Phone 5150 User Manual
Philips Clock Radio AJ3112 User Manual
Philips Indoor Furnishings 34615 31 36 User Manual
Philips Radio AJ5100DAB User Manual
Pioneer DVD Recorder DVD V7400 User Manual
Plantronics Headphones BackBeat 903+ User Manual
Polycom Webcam SP384 User Manual
Poulan Lawn Mower 175581 User Manual
ProForm Home Gym PFEL19011 User Manual