Pelco Security Camera C3403M A User Manual

OPERATION/PROGRAMMING  
Spectra® Mini Dome  
C3403M-A (3/06)  
 
Contents  
Welcome. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
5
5
How to Operate Your Dome System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Accessing Main Menu (Preset 95) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
CM6700/CM6800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
KBD200A/KBD300A (Direct Mode Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
CM9500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
CM9740/CM9760/CM9770/CM9780 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
KBD4000/KBD4002 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
MPT9500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
NET300/NET350/NET4001A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
WS5050 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
VCD5000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
6
7
7
7
7
7
8
8
8
8
8
Setup Menus – Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
9
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Display Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Label Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Dome Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Auto Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Zoom Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Zoom Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Advanced Camera Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Shutter Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
AGC Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Auto Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Auto Sharpness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Auto White Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Backlight Compensation (BLC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Video Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Motion Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Auto Flip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Proportional Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Park Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Scan Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Limit Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Azimuth Zero . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Power Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Power Up Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Line Sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
C3403M-A (3/06)  
3
 
Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Window Blanking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
Clear Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
Blank All Above/Blank All Below . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
Reset, Cycle Power, Reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Reset Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Cycle Camera Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Reboot System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Software/Language File Upload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
Upload Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
4
C3403M-A (3/06)  
 
Welcome  
Thank you for purchasing Pelco’s Spectra® Mini dome system. Your new system features a high resolution, color camera/optics  
package and programmable dome drive software.  
This manual is designed to be a reference tool for the operation and programming of your system. Inside you will find information  
about Spectra Mini’s features and commands, as well as a detailed menu tree.  
GETTING STARTED  
You will need to install your dome system before using this manual. Refer to the installation manual.  
Once installed apply power to the Spectra Mini dome system. The system will start a  
configuration sequence. When configuration is done, the following information is displayed:  
PELCO SPECTRA MINI  
VERSION X.XX  
D ADDRESS: NONE  
P ADDRESS: 1  
COMM 4800, N, 8, 1  
CONFIGURE DONE  
This information will remain on the monitor until dome operation begins.  
Refer to the following pages to learn how to operate and program your dome system.  
C3403M-A (3/06)  
5
 
How to Operate Your Dome System  
Operation  
How to Control  
Pan and Tilt  
Move joystick or press the direction keys left/right and up/down.  
Zoom Far  
To zoom far, do the following:  
1. Press the Zoom Tele button or turn the joystick clockwise until zoom stops at the 32X zoom limit.  
2. Release the button or joystick for one second.  
3. To continue zooming (digitally), press the button or turn the joystick clockwise again until you have the  
picture you want or reach the digital zoom1 limit.  
Zoom Wide  
Press the Zoom Wide button or turn the joystick counterclockwise.  
Scanning  
Stop Scan  
Preset 96  
Preset 97  
Preset 98  
Preset 99  
Random Scan  
Frame Scan  
Auto Scan  
Preset  
Refer to the documentation supplied with the control system.  
Pattern2  
Zones  
Refer to the documentation supplied with the control system.  
Refer to the Zones section and to the documentation supplied with the control system.  
Turn on or off in the programming menu. Refer to the Auto Flip section in this manual.  
Auto Flip  
1 Digital zoom magnifies the image electronically and the picture may appear pixilated. The larger the digital zoom limit the  
greater the reduction in resolution.  
2 The dome cannot do digital zoom in a pattern. Optical zoom will operate in a pattern.  
6
C3403M-A (3/06)  
 
ACCESSING MAIN MENU (Preset 95)  
You can call up the main menu on your monitor by programming (setting or creating) preset 95  
(preset 28 if in AD32-preset mode).  
Programming preset 95 for Pelco’s controllers varies according to the type of controller you are  
using. Instructions for programming preset 95 are given below for various Pelco controllers.  
CM6700/CM6800  
1. Enter the number of the Spectra dome system and press the CAM key.  
2. Enter 95 and hold the PRESET key for two seconds.  
3. In the Edit Preset menu, arrow to SET and press the ACK key. The main menu appears.  
KBD200A/KBD300A (DIRECT MODE ONLY)  
1. Enter 95.  
2. Hold the PRESET key (approximately five seconds) until the main menu appears on the  
screen.  
CM9500  
1. Enter the number of the Spectra dome system and press the CAM key. The Main menu  
appears.  
2. Highlight SETUP in the Main menu and press the SELECT key.  
3. Highlight CAM in the Setup menu and press the SELECT key.  
4. Highlight PRESET in the Camera menu and press the SELECT key.  
5. Enter 95 and press the F1 key. The main menu appears.  
CM9740/CM9760/CM9770/CM9780  
1. Press the ESCAPE key to open the Main menu. Select DEF. The Define Submenu  
appears.  
2. Enter your four-digit PIN if this is your first time entering this mode.  
3. Enter 95 and select PRST. The main menu appears on the monitor.  
4. Select the Quit icon to return to the default menu.  
(Continued on next page)  
C3403M-A (3/06)  
7
 
KBD4000/KBD4002  
1. Press the SPOT MONITOR key.  
2. Enter 95, then hold the PRESET key (approximately five seconds) until the main menu  
appears on the screen.  
MPT9500  
Standard Coaxitron Mode  
1. Enter 95 and press the PRESET SET key.  
2. Position the asterisk in the YES row and press the F1 key. The main menu appears.  
Extended Coaxitron or RS-485 Mode  
1. Enter 95 and press the PRESET SET key.  
2. Press the F2 key. The main menu appears.  
NET300/NET350/NET4001A  
1. Check the Set box.  
2. Click the preset 95 button. The main menu appears.  
WS5050  
1. Right-click in the video pane of the Spectra dome system.  
2. Click Preset and then click Select Preset.  
3. Enter 95 and then click OK.  
VCD5000  
1. Enter 95 for the preset action. The shortcuts menu appears.  
2. Press the Preset button on the KBD5000.  
8
C3403M-A (3/06)  
 
Setup Menus – Overview  
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
SYSTEM INFORMATION  
DOME SETTINGS  
DISPLAY SETUP  
PRESET LABEL  
ZONE LABEL  
ZOOM  
2 (SECS)  
2 (SECS)  
2 (SECS)  
2 (SECS)  
OFF  
DOME DRIVE MODEL  
SOFTWARE VERSION  
BIOS VERSION  
FONT VERSION  
COMM  
MINI 114R  
XX.X  
<CAMERA>  
<MOTION>  
XX.X  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
AZIMUTH/ELEVATION  
DIRECTION  
XX.X  
4800, N, 8, 1  
NONE  
1
D ADDRESS  
<PATTERN>  
P ADDRESS  
<LABEL POSTIONS>  
RESTORE FACTORY DEFAULTS  
<ZONES>  
CM9500 MODE  
32 PRESETS  
OFF  
<WINDOW BLANKING>  
<CLEAR>  
OFF  
PROTOCOL  
P
<PASSWORD>  
<ADDITIONAL>  
BACK  
EXIT  
BACK  
EXIT  
BACK  
EXIT  
ADDITIONAL  
[ZONE LABEL-------]  
[PRESET LABEL-------]  
SEE NEXT PAGE  
FREE MEMORY  
LAST RESET  
XXXXX  
X
AZIMUTH ZERO OFFSET  
MOTOR ACTIVE  
CAMERA ACTIVE  
FPGA VERSION  
VIDEO LEVEL  
0O  
YES  
YES  
X
HIGH  
SAVE AND EXIT  
CANCEL AND EXIT  
HELP  
CAMERA  
XXXX-XXXX  
ENGLISH X.XX  
LANGUAGE 1  
XXXO/-XXO  
NE  
XXX.XX  
ITALIANO X.XX  
LANGUAGE 6  
BACK  
EXIT  
Quick Programming Guide  
Access main menu (preset 95). See the Accessing Main Menu (Preset 95) section.  
Use the joystick to position the cursor beside menu selection.  
If your controller does not have a joystick, use the up or down key.  
Press Iris Open, the submenu/cursor moves to the right.  
Move the joystick up or down to view selections.  
Press Iris Open to make selection.  
Press Iris Close to cancel selection.  
C3403M-A (3/06)  
9
 
ADVANCED SETTINGS  
SHUTTER SPEED  
DOME SETTINGS  
CAMERA  
AUTO  
29  
ON  
X80  
MEDIUM  
FOCUSED  
AUTO FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
PRESET  
<CAMERA>  
AGC LIMIT  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
AUTO IRIS  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
AUTO  
76  
16  
<ADVANCED SETTINGS>  
<PATTERN>  
ON  
<ZONES>  
26  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
ON  
402  
678  
OFF  
HIGH  
BACK  
EXIT  
BACK  
EXIT  
MOTION  
AUTO FLIP  
ON  
ON  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
0
NONE  
6
SCAN SPEED (DEG/S)  
LIMIT STOPS  
ON  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
BACK  
EXIT  
POWER UP  
POWER UP ACTION  
NONE  
BACK  
EXIT  
LINE SYNC  
LINE SYNC  
LINE SYNC PHASE  
ON  
0
BACK  
EXIT  
PRESETS  
PRESET NUMBER  
1
* * * PRESET NOT DEFINED * * *  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<CLEAR PRESET>  
BACK  
EXIT  
REFERENCE INFORMATION  
AZIMUTH  
-
-
-
ELEVATION  
ZOOM  
CONTINUED ON NEXT PAGE  
10  
C3403M-A (3/06)  
 
FROM  
PREVIOUS  
PAGE  
PATTERN  
<PROGRAM PATTERN>  
<CLEAR PATTERN>  
BACK  
EXIT  
REFERENCE INFORMATION  
PATTERN USAGE  
REMAINING  
0%  
100%  
ZONES  
ZONE NUMBER  
1
* * * ZONE NOT DEFINED * * *  
<EDIT ZONE LABEL>  
<EDIT ZONE>  
NO  
OFF  
ZONE ENABLED  
ZONE BLANKING  
<CLEAR ZONE>  
BACK  
EXIT  
WINDOW BLANKING  
STYLE  
SET WINDOW  
GRAY  
<EDIT WINDOW LOCATION>  
<EDIT WINDOW ZOOM>  
BLANK ALL ABOVE  
BLANK ALL BELOW  
OFF  
OFF  
ENABLE WINDOW  
REVERSE  
NO  
<SET WINDOW>  
CLEAR WINDOW  
BACK  
EXIT  
BACK  
EXIT  
CLEAR  
CLEAR ALL ZONES  
CLEAR ALL PRESETS  
CLEAR PATTERN  
CLEAR ALL WINDOW BLANKING  
RESTORE FACTORY DEFAULTS  
BACK  
EXIT  
PASSWORD  
ENABLE PASSWORD  
<EDIT PASSWORD>  
EDIT THE PASSWORD  
----------  
OFF  
1234567890  
OK  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
CANCEL  
SPACE  
BACK  
EXIT  
BACKSPACE  
abcdefghij  
klmnopqrst  
uvwxyz#&:*  
C3403M-A (3/06)  
11  
 
Language  
The language for the on-screen menus is selectable. Available languages include English,  
Spanish, French, German, Italian, Portuguese, Russian, Polish, Turkish, and Czechoslovakian.  
The factory default language is English.  
PELCO SPECTRA MINI  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
NOTE: The dome system cannot store all 10 languages in its memory. There are two language  
packages available. The standard language package includes English, Spanish, Portuguese,  
Italian, French, and German. The alternate package includes English, Russian, Polish, Turkish,  
and Czechoslovakian. If your dome system does not have the language package that you require,  
you must upload the other language package. Refer to the Software/Language File Upload  
section.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
To change the display language:  
1. Use the joystick to position the cursor beside LANGUAGE.  
2. Press Iris Open. The cursor moves to the right, beside the current, selected language.  
3. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
All on-screen menus are changed to the selected language.  
12  
C3403M-A (3/06)  
 
System Information  
The system Information screen displays dome drive model, software version, and other  
PELCO SPECTRA MINI  
diagnostic information.  
LANGUAGE ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
System settings cannot be changed using this screen. This screen is for reference only.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
Use the following steps to display the System Information screen:  
1. Use the joystick to position the cursor beside SYSTEM INFORMATION.  
2. Press Iris Open. The SYSTEM INFORMATION window opens.  
EXIT  
SYSTEM INFORMATION  
DOME DRIVE MODEL  
SOFTWARE VERSION  
BIOS VERSION  
MINI 114R  
XX.X  
XX.X  
XX.X  
FONT VERSION  
COMM  
4800, N, 8, 1  
D ADDRESS  
P ADDRESS  
CM9500 MODE  
32 PRESETS  
PROTOCOL  
NONE  
1
OFF  
OFF  
P
<ADDITIONAL>  
BACK  
EXIT  
ADDITIONAL  
FREE MEMORY  
LAST RESET  
XXXXX  
X
AZIMUTH ZERO OFFSET  
CAMERA ACTIVE  
FPGA VERSION  
VIDEO LEVEL  
0.00o  
YES  
X
HIGH  
CAMERA  
XXXX-XXXX  
LANGUAGE 1  
LANGUAGE 2  
ENGLISH X.XX  
ESPANOL X.XX  
LANGUAGE 3  
LANGUAGE 4  
LANGUAGE 5  
LANGUAGE 6  
PORTUGUES X.XX  
DEUTSCH X.XX  
FRANCAIS X.XX  
ITALIANO X.XX  
BACK  
EXIT  
Quick Programming Guide  
(See page 9)  
C3403M-A (3/06)  
13  
 
Display Setup  
Display setup allows you to program how labels are displayed on the monitor. The following  
labels are available:  
PELCO SPECTRA MINI  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
PRESET LABEL  
ZONE LABEL  
Identifies preset.  
Identifies zone.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
ZOOM RATIO  
AZIMUTH1/ELEVATION2  
Identifies the amount of magnification.  
Amount of pan from 0° and the amount of tilt from 0° horizontal.  
Displays compass direction.  
DIRECTION  
EXIT  
A preset label is displayed when a preset is called. A zone label is displayed when the system  
moves into a zone. The zoom ratio label is displayed when zoom is activated. Azimuth/elevation  
and direction labels are displayed when pan/tilt is activated.  
DISPLAY SETUP  
PRESET LABEL  
ZONE LABEL  
ZOOM  
AZIMUTH/ELEVATION  
DIRECTION  
2 (SECS)  
2 (SECS)  
2 (SECS)  
2 (SECS)  
OFF  
The following settings are available for each label:  
OFF  
Label is not displayed when activated.  
CONSTANT  
2 SECONDS  
5 SECONDS  
10 SECONDS  
The label is continually displayed when activated.  
The label is displayed for 2 seconds after activation.  
The label is displayed for 5 seconds after activation.  
The label is displayed for 10 seconds after activation.  
<LABEL POSITIONS>  
RESTORE FACTORY DEFAULTS  
BACK  
EXIT  
1 Azimuth is the pan angle from 0° to 359°.  
2 Elevation is the tilt position from 0° (horizon) to -90°.  
14  
C3403M-A (3/06)  
 
LABEL POSITION  
Labels can be placed anywhere on the monitor. This feature allows you to customize the  
appearance of your monitor screen.  
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
The following labels are not set at fixed positions:  
PRESET LABEL  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
ZONE LABEL  
ALARM 1  
EXIT  
ZOOM RATIO - XXX.XX  
AZIMUTH1/ELEVATION2 - XXX°/-XX°  
DIRECTION - NE  
DISPLAY SETUP  
To set a label position:  
PRESET LABEL  
ZONE LABEL  
ZOOM  
AZIMUTH/ELEVATION  
DIRECTION  
2 (SECS)  
2 (SECS)  
2 (SECS)  
2 (SECS)  
OFF  
1. Use the joystick to position the cursor beside a label.  
2. Press Iris Open.  
3. Use the joystick to move the label up, down, left, and/or right.  
4. Press Iris Open.  
<LABEL POSITIONS>  
RESTORE FACTORY DEFAULTS  
5. Repeat steps 1 through 4 to position other labels.  
6. Position the cursor next to Save and Exit. Press Iris Open to save settings and exit menu.  
BACK  
EXIT  
1 Azimuth is the pan angle from 0° to 359°.  
2 Elevation is the tilt position from 0° (horizon) to -90°.  
[ZONE LABEL-------]  
[PRESET LABEL-------]  
SAVE AND EXIT  
CANCEL AND EXIT  
HELP  
XXX°/-XX°  
NE  
XXX.XX  
Quick Programming Guide  
(See page 9)  
C3403M-A (3/06)  
15  
 
Dome Settings  
CAMERA  
AUTO FOCUS  
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
Auto focus allows the lens to remain in focus during zoom-in, zoom-out, and motion functions.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
There are two auto focus settings:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
ON (default)  
If auto focus mode is set to ON, the camera will focus automati-  
cally when using pan, tilt, and zoom functions.  
OFF  
Focus is operated manually. To focus, press the Focus Far or Focus  
Near button on the controller.  
EXIT  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERN>  
<ZONES>  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
CAMERA  
AUTO FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
PRESET  
ON  
X80  
MEDIUM  
FOCUSED  
<ADVANCED SETTINGS>  
BACK  
EXIT  
16  
C3403M-A (3/06)  
 
ZOOM LIMIT  
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
Zoom limit allows the user to define a limitation on the amount of telephoto zoom. The default  
setting is 80X.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
Zoom (10X optical zoom and 8X digital zoom) can be set for 10X, 32X, 40X, or 80X.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
ZOOM SPEED  
EXIT  
Zoom speed allows the user to define how fast the dome will go from full wide zoom to the 10X  
optical zoom. The default setting is MEDIUM.  
Available settings for zoom speed include the following:  
DOME SETTINGS  
HIGH  
1.5 seconds  
2.5 seconds  
4.3 seconds  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
MEDIUM (default)  
LOW  
<PATTERN>  
<ZONES>  
NOTE: When using the HIGH setting, the image may be out of focus until zooming stops.  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
PRESET  
This option determines how fast the dome will travel to a preset position and whether the dome  
will stay in focus while moving.  
BACK  
EXIT  
FOCUSED  
FAST  
Maintains focus when going to a preset position.  
Travels quicker to a preset position and then focuses.  
CAMERA  
AUTO FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
PRESET  
ON  
X80  
MEDIUM  
FOCUSED  
<ADVANCED SETTINGS>  
BACK  
EXIT  
Quick Programming Guide  
(See page 9)  
C3403M-A (3/06)  
17  
 
ADVANCED CAMERA SETTINGS  
SHUTTER SPEED  
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
Shutter speed is the duration of the electronic shutter. Program shutter speed to operate  
automatically (Auto) or manually (Numeric Value).  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
AUTO (default)  
The electronic shutter speed is set automatically by the amount of  
light sensed by the camera.  
EXIT  
NUMERIC VALUE  
Spectra Mini system has several numerical shutter speed  
settings. The higher the number, the faster the electronic shutter.  
DOME SETTINGS  
The slowest shutter speed setting is 60 = 1/60 second  
The fastest setting is 30,000 = 1/30,000 second  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
Increasing the shutter speed lowers the light sensitivity and  
reduces the streaking of fast moving objects.  
<PATTERN>  
<ZONES>  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
NOTE: Set the shutter speed to 100 if you are using an NTSC camera in a 50 Hz environment.  
This will eliminate any flicker that may occur in the picture.  
BACK  
EXIT  
AGC LIMIT  
The AGC (automatic gain control) Limit adjusts the brightness of the pictures. Settings ranges  
from 0 to 40. The brightness increases as the number gets higher.  
CAMERA  
AUTO FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
PRESET  
ON  
X80  
MEDIUM  
FOCUSED  
<ADVANCED SETTINGS>  
BACK  
EXIT  
ADVANCED SETTINGS  
SHUTTER SPEED  
AUTO  
29  
AGC LIMIT  
AUTO IRIS  
AUTO  
76  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
16  
AUTO SHARPNESS  
SHARPNESS LEVEL  
ON  
26  
AUTO WHITE BALANCE  
R GAIN  
ON  
402  
678  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
OFF  
HIGH  
BACK  
EXIT  
18  
C3403M-A (3/06)  
 
AUTO IRIS  
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
Auto iris is the lens function that automatically opens and closes the iris in response to changing  
light conditions.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
Program the auto iris to operate automatically or at a user-defined level.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
OFF  
Auto iris is disabled, and control is always manual.  
AUTO (default)  
The iris is adjusted automatically to produce a constant video  
output as determined by the Auto Iris Level setting.  
EXIT  
NOTE: If auto iris is in the auto mode, it will remain that way until the iris is manually opened  
or closed. The dome will return to auto mode when it is panned or tilted more than 15 degrees.  
DOME SETTINGS  
Auto Iris Level  
<CAMERA>  
<MOTION>  
Auto iris level is the numeric value the auto iris uses to maintain the brightness level of the  
camera. Increase the value to brighten the scene. Decrease the level to darken the scene. This  
setting can be adjusted if the video level in the auto iris mode is too bright or too dark.  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERN>  
<ZONES>  
<WINDOW BLANKING>  
<CLEAR>  
NOTE: If backlight compensation is ON, decrease the Auto Iris Level setting.  
<PASSWORD>  
Auto Iris Peak  
Increasing the peak value will cause the auto iris circuit to react more to highlights or “peaks” in  
the picture. Decreasing this value will cause it to use the average video level to adjust the iris.  
BACK  
EXIT  
CAMERA  
AUTO FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
PRESET  
ON  
X80  
MEDIUM  
FOCUSED  
<ADVANCED SETTINGS>  
BACK  
EXIT  
ADVANCED SETTINGS  
SHUTTER SPEED  
AUTO  
29  
AGC LIMIT  
AUTO IRIS  
AUTO  
76  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
16  
AUTO SHARPNESS  
SHARPNESS LEVEL  
ON  
26  
AUTO WHITE BALANCE  
R GAIN  
ON  
402  
678  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
OFF  
HIGH  
BACK  
EXIT  
Quick Programming Guide  
(See page 9)  
C3403M-A (3/06)  
19  
 
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
AUTO SHARPNESS  
Auto sharpness enhances picture detail by increasing the aperture gain of the camera and  
sharpening the edges in the picture.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
There are two settings:  
ON (default)  
The camera automatically maintains a normal sharpness mode.  
EXIT  
OFF  
The sharpness of the picture is set manually by programming the  
SHARPNESS LEVEL. Sharpness level settings range from 0-31.  
AUTO WHITE BALANCE  
DOME SETTINGS  
This feature automatically processes the viewed image to retain color balance over a color  
temperature range. The default setting for auto white balance is ON.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERN>  
<ZONES>  
<WINDOW BLANKING>  
<CLEAR>  
R GAIN  
Adjusts the picture output in the red range. As you change the  
value, you will see the color change on your monitor.  
<PASSWORD>  
B GAIN  
Adjusts the picture output in the blue range. As you change the  
value, you will see the color change on your monitor.  
BACK  
EXIT  
CAMERA  
AUTO FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
PRESET  
ON  
X80  
MEDIUM  
FOCUSED  
<ADVANCED SETTINGS>  
BACK  
EXIT  
ADVANCED SETTINGS  
SHUTTER SPEED  
AUTO  
29  
AGC LIMIT  
AUTO IRIS  
AUTO  
76  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
16  
AUTO SHARPNESS  
SHARPNESS LEVEL  
ON  
26  
AUTO WHITE BALANCE  
R GAIN  
ON  
402  
678  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
OFF  
HIGH  
BACK  
EXIT  
20  
C3403M-A (3/06)  
 
BACKLIGHT COMPENSATION (BLC)  
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
If a bright backlight is present, the subjects in the picture may appear dark or as a silhouette.  
Backlight compensation enhances objects in the center of the picture. The dome uses the center  
of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash  
out to white. The camera will adjust the iris so that the object in the sensitive area is properly  
exposed.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
There are two backlight compensation settings:  
ON  
Backlight compensation is activated.  
OFF (default)  
Backlight compensation is not activated.  
NOTE: If backlight compensation is ON, decrease the Auto Iris setting. Refer to the Auto Iris  
DOME SETTINGS  
section.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERN>  
<ZONES>  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
VIDEO LEVEL  
Set the video output to one of the following:  
NORMAL  
1.0 volt peak-to-peak  
HIGH (default setting)  
1.2 volt peak-to-peak to compensate for losses in video cable.  
BACK  
EXIT  
CAMERA  
AUTO FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
PRESET  
ON  
X80  
MEDIUM  
FOCUSED  
<ADVANCED SETTINGS>  
BACK  
EXIT  
ADVANCED SETTINGS  
SHUTTER SPEED  
AUTO  
29  
AGC LIMIT  
AUTO IRIS  
AUTO  
76  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
16  
AUTO SHARPNESS  
SHARPNESS LEVEL  
ON  
26  
AUTO WHITE BALANCE  
R GAIN  
ON  
402  
678  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
OFF  
HIGH  
BACK  
EXIT  
Quick Programming Guide  
(See page 9)  
C3403M-A (3/06)  
21  
 
MOTION SETTINGS  
AUTO FLIP  
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
When the camera tilts downward and goes just beyond the vertical position, the dome rotates  
180 degrees. When the dome rotates (flips), the camera starts moving upward as long as you  
continue to hold the joystick in the down position. Once you let go of the joystick after the dome  
rotates, joystick control returns to normal operation. The auto flip feature is useful for following  
a person who passes directly beneath the dome.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
There are two auto flip modes:  
ON (default)  
OFF  
Auto flip mode is enabled.  
Auto flip mode is disabled.  
DOME SETTINGS  
PROPORTIONAL PAN  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERN>  
<ZONES>  
Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the  
amount of zoom. At telephoto zoom settings, the pan and tilt speeds will be slower for a given  
amount of joystick deflection than at wide zoom settings. This keeps the image from moving too  
fast on the monitor when there is a large amount of zoom.  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
There are two proportional pan modes:  
ON (default)  
OFF  
Enables the proportional pan mode.  
Disables proportional pan mode. The pan speed will not depend  
on the amount of zoom.  
BACK  
EXIT  
MOTION  
AUTO FLIP  
ON  
ON  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
0
NONE  
6
SCAN SPEED (DEG/S)  
LIMIT STOPS  
ON  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
BACK  
EXIT  
REFERENCE INFORMATION  
MANUAL LIMITS SET  
SCAN LIMITS SET  
NO  
NO  
22  
C3403M-A (3/06)  
 
PARK TIME  
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
This feature allows the dome to begin preset 1 after a programmed time of inactivity.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
Park time can be programmed from 1 minute to 720 minutes (12 hours), or it can be set to zero,  
which disables this feature. The default setting is zero.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
Park Action  
EXIT  
This feature will define the activity when the dome parks. The following settings are available:  
NONE (default)  
No action.  
PRESET 1  
Dome goes to preset 1.  
DOME SETTINGS  
SCAN SPEED  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
Scan speed is the degrees per second that the dome will pan when in a scan mode. Scan speed  
is adjustable for 3, 6, or 12 degrees per second through the programming menu. The default  
setting is 6 degrees per second.  
<PATTERN>  
<ZONES>  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
MOTION  
AUTO FLIP  
ON  
ON  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
0
NONE  
6
SCAN SPEED (DEG/S)  
LIMIT STOPS  
ON  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
BACK  
EXIT  
REFERENCE INFORMATION  
MANUAL LIMITS SET  
SCAN LIMITS SET  
NO  
NO  
Quick Programming Guide  
(See page 9)  
C3403M-A (3/06)  
23  
 
LIMIT STOPS  
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
Limit stops are programmable stops that limit the pan range of the dome. There must be two  
limits, a left and a right, to define an area.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
There are two types of limit stops:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
MANUAL  
A manual (joystick) pan operation stops when a limit stop is  
reached.  
EXIT  
SCAN  
The dome reverses direction during random, frame, or auto  
scanning when a limit stop is reached.  
To set manual or scan stops:  
DOME SETTINGS  
1. Use the joystick to position the cursor beside SET MANUAL STOPS or SET SCAN STOPS.  
2. Press Iris Open.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
3. Follow the directions displayed on the monitor.  
<PATTERN>  
<ZONES>  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
NOTE: In order for the manual or scan stops to work, the LIMIT STOPS setting must be ON.  
To clear manual or scan stops:  
1. Use the joystick to position the cursor beside CLEAR MANUAL STOPS or CLEAR SCAN  
STOPS.  
2. Press Iris Open.  
BACK  
EXIT  
3. Follow the directions displayed on the monitor.  
MOTION  
AUTO FLIP  
ON  
ON  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
0
NONE  
6
SCAN SPEED (DEG/S)  
LIMIT STOPS  
ON  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
BACK  
EXIT  
REFERENCE INFORMATION  
MANUAL LIMITS SET  
SCAN LIMITS SET  
NO  
NO  
24  
C3403M-A (3/06)  
 
AZIMUTH ZERO  
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
Azimuth is the pan angle from 0° to 359°. Azimuth zero is the pan position you specify to be the  
0° point. Azimuth zero is normally set to magnetic north. Once set, azimuth and compass  
readings are based on the set Azimuth Zero point.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
To program azimuth zero:  
1. Use the joystick to position the cursor beside SET AZIMUTH ZERO.  
2. Press Iris Open.  
EXIT  
3. Follow the directions displayed on the monitor.  
To clear azimuth zero:  
DOME SETTINGS  
1. Use the joystick to position the cursor beside CLEAR AZIMUTH ZERO.  
2. Press Iris Open.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
3. Follow the directions displayed on the monitor.  
<PATTERN>  
<ZONES>  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
MOTION  
AUTO FLIP  
ON  
ON  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
0
NONE  
6
SCAN SPEED (DEG/S)  
LIMIT STOPS  
ON  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
BACK  
EXIT  
REFERENCE INFORMATION  
MANUAL LIMITS SET  
SCAN LIMITS SET  
NO  
NO  
Quick Programming Guide  
(See page 9)  
C3403M-A (3/06)  
25  
 
POWER UP  
POWER UP ACTION  
This setting defines a specific activity (scan, preset, pattern) to be performed in the event the  
power to the dome is cycled.  
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
The following settings are available:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
NONE  
No action.  
AUTO (default)  
The dome resumes its prior activity or direction before the power  
outage.  
EXIT  
AUTO SCAN  
RANDOM SCAN  
FRAME SCAN  
PRESET 1  
Dome starts auto scan operation.  
Dome starts random scan operation.  
Dome starts frame scan operation.  
Dome goes to preset 1.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
PRESET 8  
Dome goes to preset 8.  
PATTERN 1  
Dome runs pattern 1.  
<PATTERN>  
<ZONES>  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
POWER UP  
POWER UP ACTION  
AUTO  
BACK  
EXIT  
26  
C3403M-A (3/06)  
 
LINE SYNC  
Line sync refers to a programmable function that allows you to synchronize all cameras within a  
PELCO SPECTRA MINI  
matrix system.  
LANGUAGE ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
NOTE: Spectra Mini automatically senses V-Sync input. No line sync setup is required for Pelco  
control systems that provide a V-Sync signal.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
For matrix systems that do not output V-Sync, there are two settings for line synchronization:  
ON (default)  
Adjusts the phase of the line sync to synchronize input power.  
LINE SYNC PHASE settings range from 0-359 degrees.  
EXIT  
OFF  
The dome synchronizes to an internal clock.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERN>  
<ZONES>  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
LINE SYNC  
LINE SYNC  
LINE SYNC PHASE  
ON  
0
BACK  
EXIT  
Quick Programming Guide  
(See page 9)  
C3403M-A (3/06)  
27  
 
PRESETS  
The Spectra Mini dome system has 64 preset positions. Each of the user-definable presets can  
PELCO SPECTRA MINI  
be programmed to use pan, tilt, camera settings, and motion detection. The programmable  
presets are numbered 1-32 and 35-55.  
LANGUAGE ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
The following presets are predefined for specific functions:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
Preset  
33  
Action  
EXIT  
Flip command. Pans the dome drive 180 degrees.  
34  
Pan zero command. Directs the dome drive to the factory-  
determined zero reference point.  
90-91  
92-93  
95  
Manual limit stops.  
Scan limit stops.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
Select main programming menu.  
Stop a scan.  
96  
97  
Random scanning.  
Frame scanning.  
<PATTERN>  
<ZONES>  
98  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
99  
Start auto scanning.  
Use the following steps to program a preset.  
1. Select the preset number:  
BACK  
EXIT  
a. Use the joystick to position the cursor beside PRESET NUMBER. Press Iris Open.  
The cursor moves to the right.  
b. Move the joystick up or down to view selections. Press Iris Open to enter  
selection.  
PRESETS  
2. Edit the preset label:  
PRESET NUMBER  
1
a. Use the joystick to position the cursor beside EDIT PRESET LABEL.  
b. Press Iris Open. The following appears on the monitor:  
* * * PRESET NOT DEFINED * * *  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<CLEAR PRESET>  
LABEL FOR PRESET  
PRESET NUMBER ------  
BACK  
EXIT  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
abcdefghij  
OK  
CANCEL  
SPACE  
REFERENCE INFORMATION  
AZIMUTH  
-
-
-
BACKSPACE  
ELEVATION  
klmnopqrst  
uvwxyz#&:*  
ZOOM  
c. Use the joystick to position the cursor beside a character. Press Iris Open to enter  
selection. To clear a character, position the cursor beside BACKSPACE, and then  
press Iris Open.  
d. When label is completed, move the cursor to OK. Press Iris Open to return to the  
Preset menu.  
28  
C3403M-A (3/06)  
 
3. Edit the preset scene:  
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
a. Use the joystick to position the cursor beside EDIT PRESET SCENE.  
b. Press Iris Open.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
c. Follow the directions displayed on the monitor.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERN>  
<ZONES>  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
PRESETS  
PRESET NUMBER  
1
* * * PRESET NOT DEFINED * * *  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<CLEAR PRESET>  
BACK  
EXIT  
REFERENCE INFORMATION  
AZIMUTH  
-
-
-
ELEVATION  
ZOOM  
Quick Programming Guide  
(See page 9)  
C3403M-A (3/06)  
29  
 
PATTERN  
A pattern is a memorized, repeating, series of pan, tilt, zoom and preset functions that can be  
PELCO SPECTRA MINI  
recalled with a command from a controller or automatically by a programmed function (alarm,  
park or power-up).  
LANGUAGE ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
The Spectra Mini has one user-defined pattern. Pattern length is based upon memory usage  
rather than a fixed amount of time. The complexity of the pattern will determine the amount of  
storage available to program the pattern.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
To program a pattern:  
1. Use the joystick to position the cursor beside PROGRAM PATTERN.  
2. Press Iris Open. The Patterns programming window appears on the monitor.  
3. Follow the directions displayed on the monitor.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
After the pattern is programmed, the amount of memory used is displayed on the screen.  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERN>  
<ZONES>  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
To clear a pattern:  
1. Use the joystick to position the cursor beside CLEAR PATTERN.  
2. Press Iris Open.  
3. Follow the directions displayed on the monitor.  
NOTE: When programming one or more presets within a pattern, use the normal controller  
commands to call a preset.  
BACK  
EXIT  
PATTERN  
<PROGRAM PATTERN>  
<CLEAR PATTERN>  
BACK  
EXIT  
REFERENCE INFORMATION  
PATTERN USAGE  
REMAINING  
0%  
100%  
30  
C3403M-A (3/06)  
 
ZONES  
A zone is a pan area, defined by a left and right limit, on the 360-degree pan plane. The Spectra  
PELCO SPECTRA MINI  
Mini dome system is capable of four zones, each with a 20-character label.  
LANGUAGE ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
To program a zone:  
1. Use the joystick to position the cursor beside ZONE NUMBER. Press Iris Open the cursor  
moves to the right.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
2. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
3. Use the joystick to position the cursor beside EDIT ZONE.  
EXIT  
4. Press Iris Open. The Zone programming window appears on the monitor.  
5. Follow the directions displayed on the monitor. After the left and right limit stops are  
set, the Zones menu reappears with the ZONE ENABLED option set to YES.  
DOME SETTINGS  
To edit a zone label:  
<CAMERA>  
<MOTION>  
1. Use the joystick to position the cursor beside EDIT ZONE LABEL.  
2. Press Iris Open. The following appears on the monitor:  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERN>  
<ZONES>  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
3. Use the joystick to position the cursor beside a character. Press Iris Open to enter  
selection. To clear a character, position the cursor beside BACKSPACE, and then press  
Iris Open.  
4. When the label is completed, move the cursor the OK. Press Iris Open to return to the  
Zones menu.  
BACK  
EXIT  
LABEL FOR ZONE  
ZONE NUMBER ------  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
abcdefghij  
OK  
CANCEL  
SPACE  
BACKSPACE  
ZONES  
ZONE NUMBER  
klmnopqrst  
uvwxyz#&:*  
1
* * * ZONE NOT DEFINED * * *  
<EDIT ZONE LABEL>  
To disable a zone (a zone is enabled automatically when it is programmed) or to blank a zone:  
1. Move the cursor beside ZONE ENABLED or ZONE BLANKING.  
<EDIT ZONE>  
ZONE ENABLED  
ZONE BLANKING  
NO  
OFF  
2. Press Iris Open. The cursor moves to the right.  
<CLEAR ZONE>  
BACK  
EXIT  
3. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
To clear a zone:  
1. Use the joystick to position the cursor beside CLEAR ZONE.  
2. Press Iris Open. Follow the instructions on the screen.  
Quick Programming Guide  
(See page 9)  
C3403M-A (3/06)  
31  
 
WINDOW BLANKING  
Window blanking allows a user to program one four-sided, user-defined area that cannot be  
viewed by the operator of the dome system. The blanked area will move with pan and tilt  
functions and automatically adjust in size as the lens zooms telephoto and wide.  
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
If a preset scene has window blanking, the image on the screen is blanked out when a preset is  
called. When the dome reaches the preset, the blanking is removed and the preset scene is  
displayed.  
EXIT  
Spectra Mini has two style modes for window blanking, GRAY and SMEAR. If style is set to gray,  
the blanked area is covered with a solid gray window. If smear is selected images behind the  
window will be noticeable but not distinguishable.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
To set the window blanking area:  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERN>  
<ZONES>  
1. Use the joystick to position the cursor beside WINDOW BLANKING. Press Iris Open. The  
WINDOW BLANKING menu appears on the screen.  
2. Move the joystick to position the cursor beside SET WINDOW. Press Iris Open to enter.  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
3. Use the joystick to position the cursor beside EDIT  
WINDOW LOCATION. Press Iris Open, and then follow the  
instructions that appear on the screen. When all four  
INSIDE CORNER  
corners are set, the SET WINDOW menu reappears, the  
blanked area is displayed, and the ENABLE WINDOW option is set to YES.  
BACK  
EXIT  
NOTE: Use the inside corner of the window selection tool as a guide when selecting  
the upper left, upper right, bottom right, and bottom left corners of the window.  
WINDOW BLANKING  
STYLE  
GRAY  
BLANK ALL ABOVE  
BLANK ALL BELOW  
OFF  
OFF  
<SET WINDOW>  
BACK  
EXIT  
SET WINDOW  
<EDIT WINDOW LOCATION>  
<EDIT WINDOW ZOOM>  
ENABLE WINDOW  
REVERSE  
NO  
CLEAR WINDOW  
BACK  
EXIT  
32  
C3403M-A (3/06)  
 
4. The blanked area can be programmed to turn on or off at a specified zoom point. To set  
the zoom point:  
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
a. Use the joystick to position the cursor beside EDIT WINDOW ZOOM, and then  
press Iris Open.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
b. Zoom in to the point where you want window blanking to turn on. Press Iris Open  
to set the zoom point.  
EXIT  
NOTE: Since the area is already blanked out, it may be difficult to determine when you  
want window blanking to turn on. Reverse the window before setting the zoom point.  
When finished reverse the window again to blank out the area.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERN>  
<ZONES>  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
Window Blanking Disabled  
Window Blanking Enabled  
NOTE: Increase the size of the window if any part of the blanked area is revealed during pan,  
tilt, and zoom operations.  
WINDOW BLANKING  
STYLE  
GRAY  
BLANK ALL ABOVE  
BLANK ALL BELOW  
OFF  
OFF  
<SET WINDOW>  
BACK  
EXIT  
SET WINDOW  
<EDIT WINDOW LOCATION>  
<EDIT WINDOW ZOOM>  
ENABLE WINDOW  
REVERSE  
NO  
CLEAR WINDOW  
BACK  
EXIT  
Quick Programming Guide  
(See page 9)  
C3403M-A (3/06)  
33  
 
REVERSE  
The blanked out area can be reversed to make it visible and the areas on both sides of it not visible. The areas above and below the  
blanking area remain visible. Reversing the window a second time will return it to its original condition.  
CLEAR WINDOW  
The area that has been set for window blanking is cleared.  
BLANK ALL ABOVE/BLANK ALL BELOW  
Blank All Above and Blank All Below add additional flexibility to setting up privacy areas. These settings are ideal for applications  
where a complete pan location needs to be blanked.  
Blank All Above  
Blank All Below  
Blanks everything above a user-defined tilt angle. A blanked  
band will appear at the top of the screen. The following  
settings are available:  
Blanks everything below a user-defined tilt angle. A blanked  
circle will appear below the specified angle. The following  
settings are available:  
OFF (default) - No blanking  
OFF (default) - No blanking  
0
Blanks area from horizon to 2° below horizon  
0
Blanks area from 2° to 92° below horizon  
-10 Blanks area from horizon to 10° below horizon  
-20 Blanks area from horizon to 20° below horizon  
-30 Blanks area from horizon to 30° below horizon  
-40 Blanks area from horizon to 40° below horizon  
-50 Blanks area from horizon to 50° below horizon  
-60 Blanks area from horizon to 60° below horizon  
-70 Blanks area from horizon to 70° below horizon  
-80 Blanks area from horizon to 80° below horizon  
-10 Blanks area from 10° to 92° below horizon  
-20 Blanks area from 20° to 92° below horizon  
-30 Blanks area from 30° to 92° below horizon  
-40 Blanks area from 40° to 92° below horizon  
-50 Blanks area from 50° to 92° below horizon  
-60 Blanks area from 60° to 92° below horizon  
-70 Blanks area from 70° to 92° below horizon  
-80 Blanks area from 80° to 92° below horizon  
HORIZON  
CAMERA  
30  
4
0
34  
C3403M-A (3/06)  
 
CLEAR  
Use this setting to clear user-defined settings or return the dome to factory default settings.  
PELCO SPECTRA MINI  
LANGUAGE ENGLISH  
The following are the available CLEAR settings:  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ALL ZONES  
Clears all zones. To clear a single zone, refer to the Zones  
section.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
ALL PRESETS  
Clears all presets. To clear a single preset, refer to the  
Presets section.  
EXIT  
ALL PATTERNS  
Clears the pattern.  
ALL WINDOW BLANKING  
RESTORE FACTORY DEFAULTS  
Clears the blanked window area.  
Restores all camera settings to factory default settings.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERN>  
<ZONES>  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
CLEAR  
CLEAR ALL ZONES  
CLEAR ALL PRESETS  
CLEAR PATTERN  
CLEAR ALL WINDOW BLANKING  
RESTORE FACTORY DEFAULTS  
BACK  
EXIT  
Quick Programming Guide  
(See page 9)  
C3403M-A (3/06)  
35  
 
PASSWORD  
Spectra Mini features password protection to prevent unauthorized changes to the dome  
PELCO SPECTRA MINI  
settings. An operator can open the System Information and Display Setup screens, but cannot  
access any of the Dome Settings menus.  
LANGUAGE ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
Controller/keyboard commands cannot override password-protected settings. If a keyboard is  
used to set a preset, pattern, or zone, the Enter Password screen appears on the monitor.  
The password must be entered before programming can continue.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
At least one character must be entered to create a valid password.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERN>  
<ZONES>  
<WINDOW BLANKING>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
PASSWORD  
ENABLE PASSWORD  
<EDIT PASSWORD>  
OFF  
BACK  
EXIT  
EDIT THE PASSWORD  
----------  
1234567890  
OK  
CANCEL  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
SPACE  
abcdefghij  
klmnopqrst  
uvwxyz#&:*  
BACKSPACE  
36  
C3403M-A (3/06)  
 
Reset, Cycle Power, Reboot  
PELCO SPECTRA MINI  
RESET CAMERA  
Use this function to reset all camera settings to factory default parameters.  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
CYCLE CAMERA POWER  
RESET CAMERA  
If the camera is not operating or if you lose camera control, cycle camera power. Cycling camera  
power resets the camera but does not change any saved camera settings.  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
REBOOT SYSTEM  
Reboot the system if it is not operating or if there is no control. Rebooting the system will cycle  
dome and camera power without changing programmed dome settings.  
Quick Programming Guide  
(See page 9)  
C3403M-A (3/06)  
37  
 
Software/Language File Upload  
The six-pin data port underneath the trim ring of the dome system allows access for on-site  
setup, testing, and uploading of revised operating software and language files. A Pelco field  
service tool is required to perform these operations. Field service tools include Pelcos remote  
monitor kit (IPS-RMK) and remote monitor cable (IPS-CABLE), both of which must be used with  
an adapter cable (IPS-MINIADPT).  
For instructions on how to upload revised operating software and language files refer to the  
Installation/Operation manual supplied with the field service tool.  
NOTE: Only perform software uploads when necessary. Software uploads do not need to be  
performed if the dome system is operating properly.  
UPLOAD ICON  
During a software/language file upload, an icon will appear on the monitor to indicate data is  
being transferred to the Spectra dome system (refer to the figure below). The default setting for  
data transmission is 115.2 KB per second. Noisy and long-run connections will slow the  
transmission rate.  
Upload Icon  
38  
C3403M-A (3/06)  
 
REVISION HISTORY  
Manual #  
C3403M  
C3403M-A  
Date  
12/05  
3/06  
Comments  
Orginal version.  
Removed Preset Blanking from menu. Added text to Window Blanking section that screen is blanked out when a preset  
is called.  
Pelco, the Pelco logo, and Spectra are registered trademarks of Pelco.  
© Copyright 2006, Pelco.  
All rights reserved.  
 
®
World Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East  
 

Peg Perego Motorized Toy Car RZR User Manual
Philips Baby Monitor SCD465 User Manual
Philips Computer Monitor 105B2x User Manual
Philips Flat Panel Television 15PFL4122 User Manual
Philips Landscape Lighting Broadway Road Lighting User Manual
Philips Musical Table WACS7500 User Manual
Philips Portable CD Player EXP2546 02 User Manual
Pico Macom Speaker System FM Stereo Audio Modulator User Manual
PYLE Audio Flat Panel Television PTC40LC User Manual
PYLE Audio Speaker PASW 15 User Manual