Whirlpool Washer Dryer 3SLSR6233MQ0 User Manual

®
WASHER USER INSTRUCTIONS  
Table of Contents  
ASSISTANCE OR SERVICE ............................ 1  
WASHER SAFETY............................................ 2  
WASHER USE .................................................. 3  
WASHER CARE ............................................... 4  
TROUBLESHOOTING...................................... 5  
WARRANTY...................................................... 8  
Assistance or Service  
If you need assistance or service, first see the “Troubleshooting”  
Keep this book and your sales slip together for future  
reference. You must provide proof of purchase or installation  
date for in-warranty service.  
section. Additional help is available by calling our National Call  
Center at 0800-128-940, or at:  
Johannesburg:  
Write down the following information about your appliance to help  
you obtain assistance or service if you ever need it. You will need  
to know your complete model number and serial number. You can  
find this information on the model and serial number label, located  
under the washer lid.  
Tel: (011) 621-0500  
Fax: (011) 622-7456  
Cape Town:  
Tel: (021) 659-7000  
Fax: (021) 689-7101  
Durban:  
Tel: (031) 203-2000  
Fax: (031) 203-2022  
Information may also be obtained by e-mailing us at:  
Please include a daytime phone number in your correspondence.  
Dealer name____________________________________________________  
Serial number __________________________________________________  
Address________________________________________________________  
Phone number__________________________________________________  
Model number __________________________________________________  
Purchase date __________________________________________________  
8539790  
 
WASHER USE  
Loading  
For these suggested full-sized loads, set the LOAD SIZE selector to the highest load size setting.  
SUPER CAPACITY and SUPER CAPACITY PLUS WASHERS  
Heavy Work Clothes  
Mixed Load  
Towels  
Delicates  
3 pair pants  
3 shirts  
4 pair jeans  
1 coverall  
1 overall  
3 double sheets  
4 pillowcases  
8 T-shirts  
10 bath towels  
10 hand towels  
14 washcloths  
1 bath mat  
3 camisoles  
1 quilted robe  
4 slips  
6 pair shorts  
2 shirts  
4 panties  
2 bras  
2 nighties  
1 baby’s dress  
2 blouses  
8 handkerchiefs  
EXTRA LARGE CAPACITY WASHERS  
Towels  
Heavy Work Clothes  
Mixed Load  
Delicates  
2 pair pants  
3 shirts  
3 pair jeans  
1 coverall  
2 double sheets or  
1 king size sheet(s)  
4 pillowcases  
6 T-shirts  
8 bath towels  
8 hand towels  
10 washcloths  
1 bath mat  
3 camisoles  
4 slips  
4 panties  
2 bras  
6 pair shorts  
2 shirts  
2 nighties  
2 blouses  
6 handkerchiefs  
Starting Your Washer  
WARNING  
WARNING  
Fire Hazard  
Electrical Shock Hazard  
Never place items in the washer that are dampened  
with gasoline or other flammable fluids.  
Electrically earth this appliance.  
Do not use an extension cord or an electrical portable  
outlet device.  
No washer can completely remove oil.  
Failure to follow these instructions can result in death,  
fire, or electrical shock.  
Do not dry anything that has ever had any type of oil on  
it (including cooking oils).  
Doing so can result in death, explosion, or fire.  
1. Measure detergent and pour it into the washer. If desired, add  
powdered or liquid color safe bleach. Drop a sorted load of  
clothes loosely into your washer.  
Style 1: With liquid chlorine bleach dispenser (on some  
models)  
Use only liquid chlorine bleach in this dispenser. Pour  
measured liquid chlorine bleach into the liquid chlorine  
bleach dispenser. Bleach is immediately fed into washer  
and is diluted automatically during the wash part of the  
cycle.  
Load evenly to maintain washer balance. Mix large and  
small items. Items should move easily through the wash  
water. Overloading can cause poor cleaning.  
2. (OPTIONAL) Add liquid chlorine bleach.  
NOTE: Follow the manufacturer’s directions for proper use.  
Undiluted bleach will damage any fabric it touches. The  
damage appears as rips, holes, tears, or color loss and may  
not show up until several washings later. To avoid spilling, use  
a cup with a pouring spout. Do not let bleach splash, drip, or  
run down into the washer basket. Always measure liquid  
chlorine bleach. Do not guess. Do not use more than the  
manufacturer’s recommended amount for a full load. Use less  
with a smaller load size.  
3
 
Style 2: Without liquid chlorine bleach dispenser (on some  
5. Turn the LOAD SIZE or WATER LEVEL selector to the correct  
setting for your wash load and the type of fabric being  
washed. You may change the load size or water level selection  
after the washer has started filling by turning the selector to a  
different setting.  
6. Set the TEMPERATURE selector to the correct setting for the  
type of fabric and soils being washed. Use the warmest wash  
water safe for fabric. Follow garment label instructions.  
models)  
Let the washer fill and begin agitating the load.  
Add bleach 5 minutes into the wash cycle for best  
cleaning and so that bleach can be removed in the rinse  
cycle. Pour bleach around the agitator, not directly onto  
the load to avoid damaging clothing or other items in the  
load.  
NOTE: In wash water temperatures colder than 21ºC,  
detergents do not dissolve well. Soils can be difficult to  
remove. Some fabrics can retain wear wrinkles and have  
increased pilling (the formation of small lint-like balls on the  
surface of garments).  
3. (OPTIONAL) Add liquid fabrics softener.  
NOTE: Do not spill or drip any fabric softener onto the clothes.  
Undiluted fabric softener can stain fabrics. Always dilute fabric  
softener with warm water. Too much fabric softener can make  
some items (diapers and towels) nonabsorbent. If this  
happens, do not use it every load, or use less of it in each  
load.  
7. (OPTIONAL) EXTRA RINSE selector (on some models). For an  
additional rinse and spin at the end of a wash cycle, set the  
EXTRA RINSE selector to ON. On some models, the EXTRA  
RINSE feature is part of the cycle.  
8. (OPTIONAL) Some models have an END OF CYCLE SIGNAL  
selector. Set this selector to ON if you want your washer to  
alert you when the wash cycle is complete.  
9. Push in the Cycle Control knob and turn it clockwise to the  
wash cycle you want. Reduce the wash time when using a  
small load size setting. Pull out the Cycle Control knob to start  
the washer.  
Style 1: With liquid fabric softener dispenser (on some  
models)  
Use only liquid fabric softener in this dispenser. Pour  
measured liquid fabric softener into the dispenser.  
Softener is added automatically during the rinse portion of  
the cycle. Dilute liquid fabric softener by filling the  
dispenser with warm water until liquid reaches the  
crossbar in the dispenser opening.  
To stop or restart your washer:  
Style 2: Without liquid fabric softener dispenser (on some  
models)  
To stop the washer at any time, push in the Cycle  
Control knob.  
To restart the washer, close the lid (if open) and pull out the  
Cycle Control knob.  
In the final rinse ONLY, add fabric softener that has been  
diluted with 250 mL warm water.  
4. Close the washer lid. Washer will not agitate or spin with the  
lid open.  
WASHER CARE  
Cleaning Your Washer  
Moving & Storage  
Use a soft, damp cloth or sponge to wipe up any spills such as  
detergent or bleach from the outside of your washer.  
Because some water may stay in the hoses, freezing can damage  
your washer. If storing or moving your washer during freezing  
weather, winterize it.  
Clean your washer interior by mixing 250 mL of chlorine bleach  
and 500 mL of detergent. Pour this mixture into your washer and  
run it through a complete cycle using hot water. Repeat this  
process if necessary.  
Remove any hard water deposits using only cleaners labeled as  
washer safe.  
Winterizing your washer  
1. Shut off both water faucets. Disconnect and drain water inlet  
hoses. Pour 1 L of R.V.-type antifreeze in the basket.  
2. Run washer on a drain and spin setting for about 30 seconds  
Cleaning the liquid fabric softener dispenser (on some  
models):  
to mix the antifreeze and water.  
3. Unplug washer or disconnect power.  
To use washer again  
1. Remove dispenser by grasping top with both hands and  
squeezing, while pushing upward with thumbs.  
2. Rinse dispenser under warm water, then replace it.  
1. Flush water pipes and hoses. Reconnect water inlet hoses.  
Turn on both water faucets.  
NOTE: Some models are equipped with a liquid fabric softener  
dispenser. To avoid damage to the washer or clothing do not wash  
clothes with the liquid fabric softener dispenser removed or add  
detergent or bleach to this dispenser; it is for liquid fabric softener  
only.  
2. Plug in washer or reconnect power.  
3. Run the washer through a complete cycle with 250 mL of  
detergent to clean out antifreeze.  
Storage, non-use or vacation care  
Water Inlet Hoses  
Operate your washer only when you are at home. If you will be on  
vacation or not using your washer for an extended period of time,  
you should:  
Replace inlet hoses after 5 years of use to reduce the risk of hose  
failure. Periodically inspect and replace inlet hoses if bulges,  
kinks, cuts, wear or leaks are found.  
1. Unplug washer or disconnect power.  
When replacing your inlet hoses, mark the date of replacement on  
the label with a permanent marker.  
2. Turn off the water supply to the washer. This helps avoid  
accidental flooding (due to a water pressure surge) while you  
are away.  
4
 
TROUBLESHOOTING  
First try the solutions suggested here and possibly avoid the cost of a service call...  
Washer and Components  
Washer Operation  
Noisy  
Washer stops, won’t fill, rinse or agitate  
Is the load balanced and the washer level? The wash load  
should be balanced and not overloaded. The washer must be  
level. The front feet should be properly installed and the nuts  
tightened. Reset the rear leveling legs (if needed). See the  
Installation Instructions.  
Check the following:  
Is the power cord plugged in?  
Is the indicator on the Cycle Control knob properly lined up  
with a cycle? Turn the Cycle Control knob to the right slightly  
and pull to start.  
Did you completely remove the yellow shipping strap with  
cotter pins? See the Installation Instructions.  
Are the water inlet valve screens clogged?  
Are both the hot and cold water faucets turned on?  
Is the water inlet hose kinked?  
Are the gears engaging after the drain and before spin, or  
is the upper part of agitator clicking during wash? These  
are normal washer noises.  
Does the water level seem too low, or does the washer  
appear to not fill completely? The top of the agitator is much  
higher than the highest water level. This is normal and  
necessary for clothes to move freely.  
Leaking  
Check the following:  
Has a fuse blown or is the circuit breaker open? If problem  
Are the fill hoses tight?  
continues, call an electrician.  
Are the fill hose washers properly seated?  
Are you using an extension cord? Do not use an extension  
cord or an electrical portable outlet device.  
Is the drain hose clamp properly installed? See the Installation  
Instructions.  
Is the washer in a normal pause in the cycle? The washer  
pauses for about 2 minutes during certain cycles. Allow the  
cycle to continue. Some cycles feature periods of agitation  
and soak.  
Is the sink or drain clogged? Sink and standpipe must be  
able to handle 64 L of water per minute.  
Is water deflecting off the tub ring or the load? Center the  
tub before starting the washer. The wash load should be  
balanced and not overloaded. The fill or spray rinses can  
deflect off the load. The washer must be level. The front feet  
should be properly installed and the nuts tightened. Reset the  
rear leveling legs (if needed). See the Installation Instructions.  
Is the washer overloaded? Wash smaller loads.  
Is the lid open? The lid must be closed during operation.  
Washer will not agitate or spin with the lid open.  
Washer won’t drain or spin  
Check household plumbing for leaks.  
Is the drain hose clogged, or the end of the drain hose  
more than 244 cm above the floor? See the Installation  
Instructions for proper installation of drain hose.  
Basket crooked  
Was the washer basket pulled forward during loading?  
Is the lid open? The lid must be closed during operation.  
Push the basket to the center before starting wash.  
Washer will not agitate or spin with the lid open.  
Is the load balanced and the washer level? The wash load  
should be balanced and not overloaded. The washer must be  
level. The front feet should be properly installed and the nuts  
tightened. Reset the rear leveling legs (if needed). See the  
Installation Instructions.  
Is there excessive sudsing? Always measure detergent.  
Follow manufacturer’s directions. If you have very soft water,  
you might need to use less detergent.  
Washer continues to fill or drain, cycle seems stuck  
The washer basket moves while washing. This is normal.  
Is the top of drain hose lower than the water level in  
washer? The top of the hose must be higher than the water  
level in the washer for proper operation. See the Installation  
Instructions.  
Agitator operation  
The top of the agitator is loose, or moves in only one  
direction. This is normal.  
Does the drain hose fit too tightly in the standpipe, or is it  
taped to the standpipe? The drain hose should be loose yet  
fit securely. Do not seal the drain hose with tape. The hose  
needs an air gap. See the Installation Instructions.  
Dispensers clogged or bleach leaking  
Did you follow the manufacturer’s directions when adding  
detergent and fabric softener to the dispensers (on some  
models)? Measure detergent and fabric softener. Carefully  
pour into the dispensers. Wipe up all spills. Dilute fabric  
softener in the fabric softener dispenser.  
Did you put powdered or color-safe bleach in the liquid  
chlorine bleach dispenser (on some models)? Add  
powdered or liquid color-safe bleach directly to the basket. Do  
not use the chlorine bleach dispenser for color-safe bleach.  
5
 
Wash/Rinse temperature not what I selected  
Load is wrinkled  
Are the hot and cold water inlet hoses reversed? See the  
Installation Instructions for more information. As your  
Did you unload the washer promptly? Unload the washer as  
soon as it stops.  
frequency of loads washed increases, the water temperature  
may decrease for hot and warm temperatures. This is normal.  
Did you use the right cycle for the load being washed?  
Use the cycle for Casual or Permanent Press clothes or  
another cycle with low spin speeds (if available) to reduce  
wrinkling.  
Did you select a Warm/Warm temperature setting? On  
models without ACCUWASH automatic temperature control  
that do have a Warm/Warm temperature selection, the warm  
wash will be followed by an energy saving cold rinse followed  
by warm spray rinses. This saves energy while providing the  
same rinse performance.  
Did you overload the washer? The wash load must be  
balanced and not overloaded. Loads should move freely  
during washing.  
To reduce wrinkling of permanent press clothes and some  
synthetic knits, use a large load size to provide more space.  
Washer Results  
Was the wash water warm enough to relax wrinkles, or are  
you using warm rinses? If safe for the load, use warm or hot  
wash water. Use cold rinse water.  
Load too wet  
Are the hot and cold water hoses reversed? Check to be  
sure the hot and cold water hoses are connected to the right  
faucets. See the Installation Instructions.  
Did you use the right cycle for the load being washed?  
Select a cycle with a higher spin speed (if available).  
Did you use a cold rinse? Cold rinses leave loads wetter than  
warm rinses. This is normal.  
Load is tangled or twisted  
Did you overload the washer? The wash load must be  
balanced and not overloaded. Loads should move freely  
during washing.  
Residue or lint on load  
Did you sort properly? Sort lint givers (towels, chenille) from  
lint takers (corduroy, synthetics). Also sort by color.  
Did you wrap items around the agitator? Drop items loosely  
into the washer. Do not wrap items around the agitator.  
Did you overload the washer? The wash load must be  
balanced and not overloaded. Clothes should move freely.  
Lint can be trapped in the load if overloaded. Wash smaller  
loads.  
Gray whites, dingy colors  
Did you properly sort the load? Dye transfer can occur when  
mixing whites and colors in a load. Sort dark clothes from  
whites and lights.  
Did you select the correct water level? The water level  
should be correct for the load size. Clothes should move freely  
in the water.  
Was the wash temperature too low? Use hot or warm  
washes if safe for the load. Make sure your hot water system  
is adequate to provide a hot water wash.  
Did you use enough detergent? Follow manufacturer’s  
directions. Use enough detergent to hold the lint in the water.  
Did you line dry your clothing? If so, you can expect some  
lint on the clothing.  
Did you use enough detergent, or do you have hard  
water? Use more detergent for washing heavy soils in cold or  
hard water.  
Check the following:  
Was paper or tissue left in the pockets?  
Are the hot and cold water hoses reversed? Check to be  
sure the hot and cold water hoses are connected to the right  
faucets. See the Installation Instructions.  
Is your water colder than 21°C? Wash water colder than  
21°C may not completely dissolve the detergent.  
Did you use the proper cycle time for the load? Reducing  
wash time (duration) is another way to reduce lint.  
Garments damaged  
Check the following:  
Stains on load  
Were sharp items removed from pockets before washing?  
Empty pockets, zip zippers, snap or hook fasteners before  
washing.  
Did you follow the manufacturer’s directions when adding  
detergent and fabric softener? Measure detergent and  
fabric softener. Use enough detergent to remove soil and hold  
it in suspension. Dilute fabric softener and add to the rinse  
portion of a cycle only. Do not drip fabric softener on clothes.  
Were strings and sashes tied to prevent tangling?  
Were items damaged before washing? Mend rips and broken  
threads in seams before washing.  
Is there above average iron (rust) in water? You may need  
to install an iron filter.  
Did you overload the washer? The wash load must be  
balanced and not overloaded. Loads should move freely  
during washing.  
Did you properly sort the load? Sort dark clothes from  
whites and lights.  
Did you add chlorine bleach properly? Do not pour chlorine  
bleach directly onto load. Wipe up bleach spills. Undiluted  
bleach will damage fabrics. Do not place load items on top of  
the bleach dispenser when loading and unloading the washer  
(on some models).  
Did you unload the washer promptly? To avoid dye transfer,  
unload the washer as soon as it stops.  
Did you follow the manufacturer’s care label instructions?  
6
 
Notes  
7
 
WHIRLPOOL® WASHER WARRANTY  
Warranty given and undertaken by WHIRLPOOL South Africa (PTY) LTD in respect of the  
WHIRLPOOL laundry product purchased by a client.  
WHIRLPOOL® South Africa (PTY) LTD (“WHIRLPOOL”) warrants to the original purchaser (“the client”) of the product identified by the  
serial number found on the label or plate situated on the product or on the face hereof (whichever is applicable) that for a period of  
24 months from the date of purchase shall be free of defects in materials and workmanship under normal use and service.  
The warranty is given subject to the following provisions:  
1. WHIRLPOOL shall be entitled at its sole option and discretion to either replace or repair any defective materials and/or  
workmanship.  
2. WHIRLPOOL shall carry out such warranty repair or replacement work itself or at its option through an authorized Service Partner  
free of charge provided that if the product is situated in excess of a 50-kilometer radius from the nearest WHIRLPOOL outlet or  
authorized Service Partner, then the client shall be liable to pay for such excess including any return journey at a rate per kilometer  
as is usually or normally charged by WHIRLPOOL.  
3. The client must provide WHIRLPOOL or its nominated Service Partner upon request with sufficient proof of the date and place of  
purchase of the product. Should the client be unable to provide such proof, the client will be obliged to pay normal and standard  
charges to WHIRLPOOL and/or its Service Partner.  
4. Should WHIRLPOOL or its authorized Service Partner determine that a defect or malfunction in the product has been caused solely  
or partly by the negligent acts, omissions, abuse or misuse of by the operator of the product of by an installation not in accordance  
with the Installation Instructions manual, unless the client can show otherwise, the client shall be liable for the cost of the repair and/  
or replacement including all traveling expenses thereby incurred.  
5. The warranty does not apply in the event a product is not in normal single-family domestic use, but used for commercial,  
industrial or other purpose for which it was not designed.  
6. WHIRLPOOL shall not under any circumstances whatsoever be liable for damages sustained due to failure of operation or  
malfunction of products nor for consequential damage of whatsoever nature, howsoever arising.  
7. The warranty applies only to products whilst they are situated and used within the Republic of South Africa, Swaziland, Lesotho,  
Botswana and Namibia.  
8. Any part replaced in terms of this warranty shall become the property of WHIRLPOOL or its authorized Service Partner.  
9. In the event the sale of the product was subject to special Credit Agreements Act, WHIRLPOOL warranty’s that the product shall be  
free of latent defects and WHIRLPOOL shall at its sole option repair the product as a consequence of such defects rendering.  
9.1 The client notifies WHIRLPOOL in writing immediately on becoming aware of such defects; and  
9.2 The client at their cost deliver the product to the nearest WHIRLPOOL outlet.  
10. WHIRLPOOL or its nominated independent contractor warrant that any repairs effected or parts replaced in terms of this warranty  
will be free from defective parts or workmanship for the remaining period only of the original warranty period as stipulated in clause  
one.  
11. WHIRLPOOL reserves the right to require a client to furnish WHIRLPOOL with a deposit equal to an amount determined by  
WHIRLPOOL or its authorized Service Partner prior to servicing the product during the warranty period which deposit shall be  
refunded by WHIRLPOOL to the client should the defect, failure or malfunction of the product be covered and/or provided for by the  
provisions of the warranty.  
8539790  
© 2003 Whirlpool Corporation.  
All rights reserved.  
12/03  
Printed in U.S.A.  
® Registered Trademark/TM Trademark of Whirlpool, U.S.A.  
 

Weider Home Gym WEBE07920 User Manual
Whirlpool Clothes Dryer 8533582 User Manual
Whirlpool Dishwasher W10254447B User Manual
Whirlpool Freezer EV161NZTQ User Manual
Whirlpool Range ACE2200 User Manual
Whirlpool Ventilation Hood 19760268A User Manual
Whistler Radar Detector 550 User Manual
Xantrex Technology Tablet Accessory RS2000 User Manual
Zanussi Washer TL 553 C User Manual
Zenoah Brush Cutter BCZ2600DL User Manual