3M Computer Accessories ET 3250 55 User Manual

Installing the Desktop Stand  
ET 350 Monitor and ET 3250/55 Computers  
Tool required  
Intended Use  
!
Phillips No. 2 torque screwdriver  
When properly installed using the materials provided,  
and according to these instructions, the desktop stand is  
intended to mount the ET 350 monitor and the  
ET 3250/55 computers for use on desktop or other flat  
surface.  
Installing the desktop stand  
The desktop stand is a three-piece assembly:  
!
Pivot plate with rubber foot attaches to the bottom  
of the unit.  
!
!
Mounting bracket attaches to the back of the unit.  
Angle bracket attaches to the mounting bracket.  
Warning  
Read and understand all safety information  
before installing and using this product.  
Place foam pads or other material on a flat surface to  
protect the unit’s bezel and touch screen and set the  
ET unit face-down on this surface while installing the  
desktop stand.  
To reduce the risk of fire or electric shock  
which could result in serious personal injury or  
death:  
!
Follow all product and accessory installation  
instructions.  
Attaching the pivot plate  
1. Through each of three #10-32 ½-inch screws,  
thread a lock washer.  
2. Thread the screws with lock washers through the  
Caution  
three holes on the back of the pivot plate.  
To reduce the risk of the ET unit tipping over,  
which may result in minor or moderate  
personal injury:  
3. Position the pivot plate so that each screw is  
aligned with a hole on the back of the unit  
4. Use the screwdriver to tighten the screws to a  
Do not open the bezel of the unit while it is mounted on  
the desktop stand.  
torque of 10 inch-pounds.  
Equipment  
Materials provided  
The Desktop Stand Kit includes:  
!
!
!
!
!
1 pivot plate with rubber foot  
1 mounting bracket  
1 angle bracket with rubber foot  
1 knob  
7 #10-32 ½-inch screws and lock washers  
 
the period stated in the specification. 3M Touch Systems  
makes no additional warranties, express or implied,  
including but not limited to any implied warranties of  
merchantability or fitness for a particular purpose.  
Copyright  
This manual is © 3M 2002. All rights reserved.  
Reproduction of the contents of this copyrighted manual in  
whole or in part, by any means, electronic or mechanical,  
for any purpose, without written permission of 3M Touch  
Systems, a subsidiary of 3M, is prohibited.  
User is responsible for determining whether the 3M Touch  
Systems Products are fit for User’s particular purpose and  
suitable for its method of production, including intellectual  
property liability for User's application. If a Product is  
proven not to have met 3M Touch Systems’ warranty, then  
3M Touch Systems’ sole obligation and User’s and  
Purchaser’s exclusive remedy, will be, at 3M Touch  
Systems’ option, to repair or replace that Product quantity  
or to refund its purchase price. 3M Touch Systems has no  
obligation under 3M Touch Systems’ warranty for any  
Product that has been modified or damaged through  
misuse, accident, neglect, or subsequent manufacturing  
operations or assemblies by anyone other than 3M Touch  
Systems. 3M Touch Systems shall not be liable in any  
action against it in any way related to the Products for  
any loss or damages, whether non-specified direct,  
indirect, special, incidental or consequential (including  
downtime, loss of profits or goodwill) regardless of the  
legal theory asserted. (11/01)  
Notice  
Given the variety of factors that can affect the use and  
performance of a 3M Touch Systems Product, including  
that solid state equipment has operation characteristics  
different from electromechanical equipment, some of  
which factors are uniquely within User's knowledge and  
control, it is essential that User evaluate the 3M Touch  
Systems product to determine whether it is suitable for  
User’s particular purpose and suitable for User’s method of  
application. 3M Touch Systems’ statements,  
engineering/technical information, and recommendations  
are provided for User’s convenience, but their accuracy or  
completeness is not warranted. 3M Touch Systems  
products are not specifically designed for use in medical  
devices as defined by United States federal law. 3M Touch  
Systems products should not be used in such applications  
without 3M Touch Systems’ express written consent. User  
should contact its sales representative if User’s opportunity  
involves a medical device application.  
Edition  
Second edition: January 2002  
Document Number: 13892 (Rev. 1.1)  
Important notice to purchaser  
Specifications are subject to change without notice. 3M  
Touch Systems’ Products are warranted to meet their  
published specifications from the date of shipment and for  
Trademark  
3M Dynapro is a trademark of 3M.  
 
Worldwide Manufacturing Plants  
3M Touch Systems  
3M Optical Systems Division  
For more information on 3M touch products, visit  
3Mtouch.com or call toll-free 1-800-667-0374.  
Austin, Texas  
Methuen, Massachusetts  
Milwaukee, Wisconsin  
Vancouver, BC, Canada  
Abingdon, UK  
800 Carleton Court  
Annacis Island  
New Westminster, BC  
Canada V3M 6L3  
© 3M 2002  
13892 (Rev. 1.1)  
 

3M Marine Instruments 3MTM User Manual
Actiontec electronic Network Router HSP56I User Manual
Adder Technology Computer Hardware DDC Ghost User Manual
ADTRAN Network Router 1200130L2 User Manual
ADTRAN Switch ADT 1234POE User Manual
Airfree Air Cleaner Enviro 60 User Manual
Airlink101 Network Card AWLC3026T User Manual
Alto Shaam Oven 714ES over User Manual
ATI Technologies Computer Drive 117 40122 20 User Manual
Behringer DJ Equipment KX1200 User Manual