Airlink101 Switch AKVM 2A User Manual

Step 2 Connect the shared keyboard, monitor,  
mouse, microphone, and speakers to the main KVM  
unit. See Fig. 1.1  
Ver. 1A  
Front-panel button  
The front-panel button lets you directly switch be-  
tween the computers. Simply press the button on the  
KVM unit to select the computer. By default, PC port  
switching and audio port switching are bound together.  
Quick Installation Guide  
Model #AKVM-2A  
If you want to disable the binding of PC and audio port  
switching, use the hotkey sequence, ScrLk + ScrLk  
+ W. To enable the binding again, just click ScrLk +  
ScrLk + Q.  
Hotkey Sequence  
The hotkey sequence consists of three specific  
keystrokes pressd on the keyboard.  
Fig 1.1  
Hotkey sequence = ScrLk + ScrLk + Command key  
The two consecutive ScrLk key should be pressed  
within 2 seconds and the following command key(s)  
should also be pressed within 2 seconds. Otherwise,  
the hotkey sequence will not be validated.  
Section 1  
Step 3 Connect each set of the built-in KVM cables  
to a computer’s keyboard, video, mouse, micro-  
phone, and speaker ports. You can use individual  
standard keyboard, mouse, video, and audio cables  
to extend the cable distance, but depending on the  
type of cables you use, the maximum cable dis-  
tance is limited to 5 ~ 7 meters (15.5 ~ 23 feet).  
Introduction  
The AKVM-2A switch is a 2-port PS/2 type KVM switch  
with audio support that comes with two sets of built-in  
1.5M cables. It enables users to access, control, boot,  
and reboot two computers using only one keyboard, video  
monitor, mouse, microphone, and speakers. Its one-  
piece design offers more portability and convenience to  
users than conventional KVM switches.  
For detailed Hotkey sequences and their correspond-  
ing functions, please refer to the Quick Reference  
Chart on back.  
1
Step 4 Power up the connected computers one by  
one. After the computers are powered up, the  
keyboard and mouse will be recognized and you can  
begin operating the KVM switch.  
Section 4  
Technical Support  
Section 2  
Section 3  
Installation  
Toll free: 1-888-746-3238  
Before connecting any cable, please make sure all of your  
computers and their peripherals have been powered off.  
Otherwise, the KVM switch may not be set up properly.  
Operations  
There are two methods to select a specific computer:  
Copyright © 2005 AirLink101. All rights reserved. AirLink101, the stylized AirLink101 logo,  
specific product designations, and all other words and logos that are identified as trademarks  
and/or service marks are, unless noted otherwise, the trademarks and service marks of  
AirLink101. All other product or service names are the property of their respective holders.  
AirLink101 products are protected under numerous U.S. and foreign patents and pending  
applications, mask work rights, and copyrights.  
Step 1 Make sure all the computers that are to be  
connected to the KVM switch and their peripherals  
are powered-off. If not, power them off before you  
proceed with the following steps.  
Using the front-panel button or the hotkey  
sequence.  
Continue on Back  
 

Abbyy USA Scanner SERVER 32 User Manual
Agri Fab Snow Blower 45 0418 User Manual
Amana Dishwasher ADB1600AW User Manual
American Standard Humidifier 200A User Manual
Apple Network Card QuickTime Streaming Server Darwin Streaming Server User Manual
Audiovox Automobile Alarm TSP 575 User Manual
Avital Remote Starter 6501 User Manual
Axis Communications Security Camera Axis P3225 User Manual
Axor Indoor Furnishings 34010XX1 User Manual
Beko Dishwasher DFS1530 User Manual