Audiovox Automobile Alarm SS9000 User Manual

Model SS9000  
Owner’s Manual  
Long Range Remote Start Security System  
With Plug-In Shock Sensor & Starter Disable  
IMPORTANT! In order to provide you with the highest level of security to your  
vehicle, this system is equipped with selectable manual override circuitry. It is  
possible that you will need to override you security system if the transmitter  
becomes lost, or inoperative due to battery failure. Reading the sections on  
"Manually Overriding Your System" is necessary to fully understand the procedure  
required to enable your vehicle in such situations. In addition, the chart on the last  
page of this manual has a section for the particular features and options installed  
in your vehicle as well as the override method selected. Although the default  
mode is "Valet Switch" operation, the system can be configured for "Custom  
Code" operation for enhanced security. Confirm the override mode selected on  
the last page of this manual, and familiarize yourself with the section on it's opera-  
tion.  
FEATURES :  
1 Two Way 5 Button Rechargable LCD Remote Control and 1 One Way 5  
Button Remote Control  
Seven Channel Code Learning Programmable Receiver  
External Spread Spectrum PB/LED Transceiver Antenna  
Single Or Two User Programmable W/Separate Control Outputs  
Single Button Lock/Unlock or Separate Button Lock/Unlock or Both  
Remote Keyless Entry With Optional Access Guard (must have power door  
locks)  
Selectable Manual Override Mode  
New Enhanced Panic Feature (Any button other than unlock stops siren, no  
change to the units state)  
Smart Disarm (If triggered, elect to shut off siren, or disarm entire unit )  
Adjustable Shock Sensor Via The Transmitter (Pre-Detect Off, Pre & Full Detect  
Off, City Mode)  
Safe Start Output Controlled From Channel 3 (Option Channel 3 For Trunk, Or  
For R/S)  
24 Hour Time Start Mode  
Cold Temperature Start Mode  
2 or 4 Hour Automatic Start Mode  
Parking Meter Count Down Timer On LCD Remote  
Additional Count Down Timer Mode  
Remote Panic In All Modes (Press & Hold Lock /Unlock Button For 3 Seconds  
To Engage)  
Improved Custom Code Override, User Selectable and Programmable  
Protected PBLED, (Push Button LED Valet/Program/Manual Override Switch )  
7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming  
Intrusion Alert With Memory  
Instant Siren Activation  
Starter Disable Output  
128-8842  
1 of 20  
 
simply press button 1, (lock), two times within a one second  
time period. The system will now respond to that transmitter  
each time a button is pressed.  
NOTE: This system is custom configurable and can be set up to  
operate with a number of options controlled from any transmit-  
ter button or button combination. For reference, we will describe  
operation assuming that your system is pro-  
grammed for separate lock and unlock buttons. Also  
reference will be made to the icons as shown on  
the buttons.  
NOTE: The LCD based remote will be explained in  
detail further in this manual See "System Status"  
described later in this manual. Consult your  
installation center if your system has been configured differently.  
NOTE: Your system has the option of using a siren, the vehicle horn,  
or both for the sounding device. Where the siren is referenced be-  
low, the horn or both may in fact chirp, or beep.  
ARMING THE SYSTEM - ACTIVE  
1. Turn off the engine, exit the vehicle, and close all doors, hood lid  
and trunk lid.  
2. Press and release Lock/Arm button on the keychain transmitter.  
The Antenna's LED begins to flash slowly.  
Parking Lights flash one time.  
Siren sounds one chirp.  
If the siren/horn sounds 3 chirps, then you have left a door, trunk, or  
hood lid ajar. Simply close the opened entry point to provide full protec-  
tion. If the siren "chirped" three times, sometime after arming, the  
exclusive delayed dome light learn circuit has been programmed and  
the system detected a open entry point after the learned delay expired.  
Again, closing the hood, trunk, or doors will correct the problem and you  
do not need to disarm the system to make the correction. If the siren/  
horn did not sound when arming, then the chirps have been turned off  
and you should refer to the section titled "ELIMINATING THE ARM/DIS-  
ARM CHIRPS" in this manual.  
Doors Lock - Optional  
NOTE: If the optional Headlamp illumination feature has been added, and has  
been selected for operation when arming, as an added convenience, the  
system will turn on the headlights when the system is armed.  
SILENT ARMING - ACTIVE (Must be activated during programming)  
1. Turn off the engine, exit the vehicle and close all doors, hood lid and trunk lid.  
2. Press and hold the Lock/Arm button on the keychain transmitter for 2  
seconds.  
The Antenna's LED begins to flash slowly.  
Parking Lights flash one time.  
Siren will not sound.  
If the siren "chirped" three times, sometime after arming, the exclusive delayed  
dome light learn circuit has been programmed and the system detected a open  
entry point after the learned delay expired. Closing the hood, trunk, or doors will  
correct the problem and you do not need to disarm the system to make the  
correction.  
Page 3  
128-8842  
3 of 20  
 
Doors Lock - Optional  
NOTE: If the optional Headlamp illumination feature has been added and has  
been selected for operation when arming, as an added convenience, the sys-  
tem will turn on the headlights when the system is armed.  
The LCD Remote has the following response:  
ARMING THE SYSTEM - PASSIVE (AUTOMATIC)  
(Must be activated during programming)  
1. Turn off the engine, exit the vehicle and close and lock all doors, hood lid and  
trunk lid.  
The Antenna's LED begins to flash rapidly, indicating 30 second passive  
arming has begun.  
2. Opening any protected entry point during the 30 second passive arming cycle  
will immediately suspend automatic arming and the 30 second passive arm-  
ing cycle will re-start when all doors are closed. At the end of the passive  
arming cycle;  
The Antenna's LED begins to flash slowly.  
Parking Lights flash one time.  
Siren sounds one chirp  
If the siren did not sound when arming, then the chirps have been turned off and  
you should refer to the section titled “ELIMINATING THEARM / DISARM CHIRPS“  
in this manual.  
Doors Lock - Optional  
Door locking during passive arming is a selectable feature. The alarm can be  
programmed to allow the doors to lock only when arming using the keychain  
transmitter and they will not automatically lock during passive arming.  
PROTECTION WHILE THE SYSTEM IS ARMED  
Opening any protected door, hood or trunk lid will cause the alarm to imme-  
diately sound. The alarm will continue to sound for 30 seconds, then stop and  
continue to monitor all protected entry points. If the thief left a door opened, the  
alarm will sound for six 30 second cycles, remain armed and ignore that trig-  
gered zone.  
Whenever the system is armed, the Antenna's LED indicator will slowly flash.  
This serves as a visual deterrent to the potential thief. The LED is a very low  
current bulb and will not cause the vehicle’s battery to drain, even when left  
unattended for extended periods.  
Whenever the system is triggered, the vehicle’s parking lights will flash for the  
full 30 second alarm cycle, attracting visual attention to the vehicle.  
Optional - Whenever the system is armed, the vehicle’s starting circuit will be  
bypassed. If the thief should choose to ignore the siren, the vehicle can not be  
started.  
Any mild impact to the vehicle’s glass will cause the alarm to sound a short  
series of warning tones.  
Any strong impact to the vehicle’s glass will cause the alarm to trigger for the  
full 30 second alarm cycle.  
NOTE: If the optional interior illumination circuit was installed, the interior light  
will flash as well for the full 30 second alarm cycle.  
Page 4  
128-8842  
4 of 20  
 
DISARMING THE SYSTEM  
NOTE: If the optional 2 step door unlock circuit is installed, when the unlock  
transmitter button is activated, the drivers door only will unlock, pressing the  
unlock button a second time will cause all doors to unlock.  
NOTE: If your transmitter has been configured with single button Lock/Unlock, to  
activate the all door unlock feature operate the Lock/Unlock button a second  
time within 3 seconds of the first unlock command.  
1. As you approach the vehicle, press and release the Unlock/Disarm button on  
the keychain transmitter.  
The Antenna's LED turns off.  
The LED will start flashing rapidly, indicating that the system is re-arming  
automatically. Open any door to suspend the automatic arming.  
Parking Lights flash two times.  
If the parking lights flashed three times, then the alarm was triggered in your  
absence. Before turning the key on, examine the LED to identify which zone was  
triggered.  
Siren sounds two chirps.  
If the siren sounds 4 chirps, then the alarm was triggered in your absence. Before  
turning the key on, examine the LED and refer to the INTRUSION WARNING  
SIGNALS section of this manual to identify which zone was triggered.  
If the siren did not sound when disarming, then the chirps have been turned off  
and you should refer to the section titled “ELIMINATING THE ARM / DISARM  
CHIRPS“ in this manual.  
Doors Unlock - Optional  
2 Step Doors Unlock - Optional  
NOTE: If the optional Headlamp illumination feature has been added and has  
been selected for operation when disarming, as an added convenience, the  
system will turn on the headlights when the system is disarmed.  
SILENT DISARMING (Must be activated during programming)  
NOTE: If the optional 2 step door unlock circuit is installed, when the unlock  
transmitter button is activated, the drivers door only will unlock, pressing the  
unlock button a second time will cause all doors to unlock.  
NOTE: If your transmitter has been configured with single button Lock/Unlock as  
shown, to activate the all door unlock feature operate the Lock/Unlock button a  
second time within 3 seconds of the first unlock command.  
1. Press and hold button the Unlock/Disarm button on the keychain transmitter for  
2 seconds.  
The Antenna's LED turns off.  
The LED will start flashing rapidly, indicating that the system is re-arming  
automatically. Open any door to suspend the automatic arming.  
Parking Lights flash two times.  
If the parking lights flashed three times, then the alarm was triggered in your  
absence. Before turning the key on, examine the LED to identify which zone was  
triggered.  
Siren will not sound.  
Page 5  
128-8842  
5 of 20  
 
If the siren sounds 4 chirps, then the alarm was triggered in your absence.  
Before turning the key on, examine the LED and refer to the INTRUSION  
WARNING SIGNALS section of this manual to identify which zone was triggered.  
Doors Unlock - Optional  
2 Step Doors Unlock - Optional  
NOTE: If the optional Headlamp illumination feature has been added and has  
been selected for operation when disarming, as an added convenience, the  
system will turn on the headlights when the system is disarmed.  
WHILE THE SYSTEM IS SOUNDING  
If during a triggered state, you wish to shut off the siren without disarming your  
security system, simply press and release any transmitter button other than the  
Unlock/Disarm button. This action will turn off the siren yet leave the vehicle fully  
armed and protected. This feature is particularly useful if you are aware of children  
playing near your vehicle that may accidently trigger your security system. In this  
case you can cancel the siren sounding without disarming your alarm.  
INTRUSION WARNING SIGNALS  
This system will inform you if an intrusion attempt has occurred while you were  
away from the vehicle. If an intrusion attempt has occurred, the siren will  
chirp 4 times and the parking lights will flash 3 times when disarming the  
system. Enter the vehicle and observe the Antenna's LED to identify which  
zone was triggered.  
If the LED is flashing one time...pause...one time...pause...etc., then an  
intrusion attempt was made to the shock sensor, or an accessory trigger-  
ing device that may have been added to the system.  
If the LED is flashing two times...pause...two times...pause...etc., then  
an intrusion attempt was made to a hood or trunk pin switch that was  
added to the system or to a light activated entry point if the alarm was  
installed using the voltage sensing feature.  
If the LED is flashing three times...pause...three times...pause...etc.,  
then an intrusion attempt was made through one of the vehicle’s doors.  
These intrusion warning indicators are stored in the system’s memory and will  
only be erased when the ignition key is turned on.  
PUSH-BUTTON LED RECEIVER VALET/OVERRIDE/SAFETYCONTROLSWITCH  
The Push-Button LED switch located in the receiver allows you to temporarily  
bypass all alarm functions, eliminating the need to hand your transmitter to  
parking attendants or garage mechanics. When the system is in valet mode, all  
alarm functions are bypassed, however the remote panic feature and remote  
door locks will remain operational. To use the valet mode, the system must first  
be disarmed either by using your keychain transmitter, or by activating your per-  
sonalized manual override code.  
1. Enter the vehicle, and turn the ignition key to the on position.  
2. Press and hold the Push-Button switch until the LED turns on solid. The  
system will remain in the valet mode.  
3. To return to normal operation, press and release the Push-Button switch any  
time the ignition is on.  
NOTE: Always remember to return the vehicle to the valet off position. This will  
ensure that the vehicle remains protected at all times.  
Page 6  
128-8842  
6 of 20  
 
MANUALLYOVERRIDINGYOUR SYSTEM:  
Using The Receiver's Push-Button Override Switch  
Your Security System can be disarmed without the use of the keychain transmitter.  
This is necessary, since you will need the ability to operate your vehicle if the  
transmitter is lost or its battery fails. If your system has been selected for Valet  
Switch manual override as indicated on the last page of this manual, to bypass  
the alarm system;  
1. Open the vehicle door. The alarm will sound.  
2. Turn the ignition key to the on position.  
3. Within 5 seconds, press and release the receiver's push-button override  
switch.  
The alarm system will stop sounding and enter the (bypassed) mode. You can  
now start and operate the vehicle normally.  
Typically this override mode is used only if the transmitter has become inopera-  
tive.  
Programming Your Custom Override Code:  
Unlike override switches easily found, and defeated, this security system allows  
the consumer to program a personal override code, offering a higher level of  
security. To take advantage of this option, programmable feature # 10 must be  
selected for the Custom Code Option. Consult your installation center for pro-  
gramming details. The system comes from the factory with a pre-programmed  
override code of 11. To change this default override code, do the following:  
1. Disarm the system by use of the transmitter, or by use of the emergency  
override sequence. Turn the ignition switch to the on position.  
2. Within 10 seconds, press and release the Receiver's Push-button switch, 3  
times.  
3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.  
(The siren or horn will beep and the lights will flash one time.)  
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and  
releasing the Receiver's Push-button switch from 1 up to 9 times.  
5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off  
then on.  
6. Within 10 seconds, begin to enter your chosen units digit by pressing and  
releasing the Receiver's Push-button switch from 1 up to 9 times.  
7. Finish by turning the ignition switch to the off position.  
If the new code was accepted, the unit will report back the newly entered code, by  
flashing the LED, first indicating the 10ths digit, pause and then the units digit.  
The unit will report the new code three times with a one second pause between  
each code, then the system will begin arming. If the LED flash pattern reports the  
previously stored code, the new code was not entered correctly. Please repeat  
steps 1 through 7 above considering the following.  
NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize  
a 0 (Zero), or no digit entered in any place, units or tenths.  
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for  
more then 5 seconds during any of the above steps, the unit will revert  
back to the last successfully stored code.  
Custom Code Programming Example:  
To Change the code from the factory pre-assigned code of 11 to “52” you would do  
the following:  
Page 7  
128-8842  
7 of 20  
 
1. Disarm the system by use of the transmitter, or by use of the emergency  
override sequence.  
2. Turn the ignition switch to the on position.  
3. Within 10 seconds, press and release the Receiver,s Push-button switch, 3  
times.  
4. Within 10 seconds turn the ignition switch off, on, off, on, off, on.  
(The siren or horn will beep and the lights will flash one time.)  
5. Within 10 seconds, begin to press and release the Receiver's Push-button  
switch to set the tenths digit. (As per the example, press and release 5 times  
to set the tenths digit to 5)  
6. Within 10 seconds of the last press of the pushbutton, turn the ignition switch off  
then on.  
7. Within 10 seconds, begin to press and release the Receiver's Push-button  
switch to set the units digit.  
(As per the example, press and release 2 times to set the units digit to 2).  
8. Turn the ignition switch to the off position. Immediately observe the LED flash  
pattern.  
You will note the LED flashing five times, pause, and then flash two times, pause. This  
pattern will be repeated three times indicating the new code (52) has been accepted and  
stored in memory.  
NOTE: If after step 7, the LED flashes a code other than what was just entered,  
this indicates that the code has not been changed. You will have to repeat  
steps 1 through 7 above being certain to note the following:  
Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0  
(Zero), or no digit entered in any place, units or tenths.  
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more  
then 5 seconds during any of the above steps, the unit will revert back to the last  
successfully stored code.  
MANUALLYOVERRIDINGYOUR SYSTEM:USING THE CUSTOM CODE OVERRIDE  
Assuming the override code programmed has not been changed, and the default  
override code of 11 is in the system's memory.  
1) Enter the vehicle and turn the ignition switch to the on position.  
NOTE: The siren will sound.  
2) Within 5 seconds, press and release the Receiver's Push-button switch 1  
time.  
3) Within 5 seconds, turn the ignition switch off then on.  
4) Within 5 seconds, press and release the Receiver's Push-button switch 1  
time.  
5) Turn the ignition switch off then on and start the vehicle.  
NOTE: If you have changed the programmed override code then substitute your  
new code tenths for step 2 above, and units for step 5 above.  
ELIMINATING THE NORMAL ARM/DISARM CHIRPS  
You can selectively eliminate the normal arm & disarm chirps by holding the  
transmitter button slightly longer when arming or disarming. This will prevent the  
siren chirps for one arm or disarm cycle. If you find this inconvenient and wish to  
eliminate these chirps permanently,  
1. Turn the ignition switch 'on" then 'off".  
2. Within 10 seconds of turning off the ignition, press and release the Receiver's  
Push-button switch 3 times.  
Page 8  
128-8842  
8 of 20  
 
3. If the chirps were on before you started, the siren will emit 2 short chirps  
indicating that the chirps are now off. If the chirps were off before you started,  
the siren will emit one short chirp indicating that the chirps are now on.  
NOTE: If the vehicle battery is disconnected then reconnected, the unit will return  
to the default setting of chirps on. Repeat the above procedure to  
eliminate the arm/disarm chirps.  
NOTE: Whenever the chirps are bypassed, the 4-chirp intrusion indicator and  
3 chirp defective zone indicator will always operate. Since these are  
important warnings to you that something has happened, they cannot be  
eliminated.  
NOTE: Your system must be programmed by the installation center to  
enable this feature.  
REMOTE PANIC OPERATION  
The Lock or Unlock button on your keychain transmitter also functions as a panic  
switch for use in emergency situations. To use remote panic:  
1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or  
more seconds. The alarm will immediately sound.  
2. To stop the alarm, press and hold the Lock or Unlock button on the transmitter  
again for 3 seconds. If the button is not pressed, the alarm will automatically  
stop after 30 seconds. Also if any transmitter button other than the Lock or  
Unlock button is pressed and released, the Panic mode will be turned off  
immediately. The normal function of this transmitter button will be suspended  
during the Panic sounding period.  
3. During the panic mode, the Lock and Unlock buttons can be used to lock and  
unlock the doors, (if the option is installed), however once the unlock/disarm  
button is pressed, the vehicle's starter inhibit device, (where installed) will be  
disabled allowing the vehicle to start.  
NOTE: While in the Panic mode, pressing and releasing the Lock or Unlock  
buttons will, if the option is installed, lock and unlock the doors respectively. While  
in the panic mode, anytime the Unlock button is pressed, the panic feature will  
continue for the allotted 30 seconds, however, the security system will be dis-  
armed allowing the vehicle to start.  
RF SHOCK SENSOR MODE SELECTION  
The way in which your alarm system reacts to threatening vibrations, created by  
attempts to enter the vehicle by breaking a window, is adjustable by the transmitter  
immediately after arming. There are 4 modes of operation that can be selected  
by the operator:  
1. Normal Operation (default mode)  
In this mode, any strong vibrations will cause the siren to sound (full  
detect) for 30 seconds. Any lesser vibration will cause the siren to emit  
about 6 short warn away chirps, (pre-detect).  
2. Stage 1 (Omit pre-detect)  
In this mode, the warn away chirps created by the lesser vibration will be  
deleted. If strong vibration occurs, the siren will sound.  
3. Stage 2 (Omit pre & full detect)  
In this mode, both the pre-detect stage and the full trigger stage of the sensor  
are defeated. The unit will not react to vibration of any magnitude.  
NOTE: Shock Sensor Icon Is Displayed On The LCD Panel.  
Page 9  
128-8842  
9 of 20  
 
4. Stage 3 (City Mode)  
In this mode, the pre-detect chirps will change from six pre-warning tones to  
a full 10 seconds of warning chirps.  
The full detect trigger duration will be reduced from 30 seconds to 15 seconds.  
NOTE: Setting the stage of the shock sensor will be effective for one arming cycle  
only. Once the system has been disarmed, the very next arming cycle will  
cause the sensor to default to the normal operation stage.  
To change or adjust the shock sensor, press and release the ARM button of you  
keychain transmitter.  
1. Within 2 seconds of arming, press and release the ARM button 1 time, to  
defeat the pre-detect stage of the shock sensor. (The lights will flash and the  
siren will chirp once.)  
2. Within 2 seconds of step 1, press and release the ARM button 2 times, to  
defeat the pre and full detect stages of the shock sensor. (The lights will  
flash and the siren will chirp twice.)  
3. Within 2 seconds of step 1, press and release the ARM button 3 times to  
enter the "City Mode" of operation. (The lights will flash and the siren will chirp  
three times.)  
While under control of the remote start the system can be programmed to allow  
you to shunt the shock sensor from the transmitter. If the system has been such  
programmed, simply press the lock button of your keychain transmitter anytime  
during the remote start cycle. The shock sensor will be shunted for the entire run  
cycle and will resume normal operation after the remote start unit shuts off.  
Check with your installation center to determine if this feature has been pro-  
grammed into your system.  
PUSH- BUTTON LED RECEIVER SAFETY CONTROL SWITCH  
The Push-Button LED control switch allows you to temporarily disable the remote  
starting function of the system. This recommended whenever the vehicle is being  
serviced. To place the system in the service mode:  
1) With the system disarmed/unlocked, and the ignition switch off Press and  
Hold the Push-Button, found on the windsheild receiver, in.  
2) Turn the ignition switch on, off, on, off, on, off.  
3) The LED begins to flash two short flashes followed by one long flashes and  
continues this pattern until returned to normal mode of operation.  
This puts the unit into the R/S Override mode indicating that the remote start is  
in the service mode and will not start from RF or any other input Posse or  
otherwise.  
To Exit R/S Override Mode  
1) With the system disarmed, Press and Hold the Push-Button, found on the  
windsheild receiver, in.  
2) Turn the ignition switch on, off, on, off, on, off.  
3) The LED turns off indicating that the R/S unit is fully functional one again.  
REMOTE STARTING THE VEHICLE  
The system WILL NOT start the vehicle if any one of the following conditions  
exists:  
1. The Vehicle Hood Is Opened.  
2. The Gear Selector Is In Any Gear Other Then Park.  
3. The Brake Is Depressed.  
4. The System is in the Remote Start Override mode  
Page 10  
128-8842  
10 of 20  
 
WARNING! Be certain that the vehicle is outdoors before using this or any remote  
vehicle starting device. A running engine produces dangerous carbon  
monoxide fumes which can be harmful or fatal if prolonged exposure  
occurs. DO NOT remote start the vehicle if it is garaged.  
To Remote Start The Vehicle:  
Press and release the programmed channel of your keychain transmitter two  
times within 2 seconds. The vehicle will start and remain running for the pre-  
programmed 5, 10, 15, 20, 45 & 60 minutes. As a visual indication, the parking  
lights will flash or turn on depending on the programming set up by your instal-  
lation center.  
When you arrive at your vehicle, disarm the alarm system by pressing and re-  
leasing the arm/disarm button of your keychain transmitter. Enter the vehicle and  
turn the ignition key to the on position.  
CAUTION! Do not turn the key to the start position. This will cause the starter  
motor to engage with the already running engine which could result in  
damage. Step on the brake pedal to disengage the remote start unit.  
The vehicle will continue to run but now on it's own power.  
NOTE: The engine will stop running before the expiration of the pre-programmed  
run timer if you complete any of the following:  
1. Press and release the programmed channel of your keychain transmitter two  
times within 2 seconds.  
2. Depress the brake pedal.  
3. Open the hood.  
4. Place the system in the Remote Start Override mode.  
5. Race the engine to above 4000 RPM.  
NOTE: This system has the ability to be configured to a single press start if you so  
desire. Please check with your installation center if your system was  
changed from the default safe start setting of two press start or if you wish  
to change your configuration.  
OPERATING ONAUTOMATIC START UP TIMER MODE  
Your system has the ability to automatically start the vehicle every 2 or 4 hours  
over a 48 hour period. This feature is especially useful in cold climates where  
the only means to keep the engine and engine fluids warm is to periodically start  
the engine.  
WARNING! Be certain that the vehicle is outdoors before using this or any re-  
mote vehicle starting device. A running engine produces dangerous  
carbon monoxide fumes which can be harmful or fatal if prolonged  
exposure occurs. DO NOT remote start the vehicle if it is garaged.  
TO BEGIN THEAUTOMATIC START UPTIMER  
1. Turn the ignition key on then off.  
2. Within 10 seconds, activate the RF start command two times. (Push the  
programmed channel button of your keychain transmitter 4 times).  
The parking lights will flash and the siren will chirp 4 times indicating the timed  
start mode is activated.  
The vehicle, on a 2 or 4 hour interval basis, will automatically start, run for  
the pre-programmed time (5,10,15,20, 45, or 60 minutes), and then shut off.  
This will continue for 48 hours.  
Page 11  
128-8842  
11 of 20  
 
NOTE: The automatic start up timer can also be initiated from the keychain  
transmitter. To do this:  
1. Start the vehicle using the keychain transmitter by pressing and releasing the  
second channel transmitter button 2 times.  
2. Shut off the vehicle using the keychain transmitter by pressing and releasing  
the second channel transmitter button 2 times.  
3. Within 10 seconds of step 2, activate the RF start command two times. (Push  
the second channel button of your keychain transmitter 4 times).  
The parking lights will flash and the siren will chirp 4 times indicating the timed  
start mode is activated.  
CANCELING THEAUTOMATIC START UPTIMER  
To cancel the automatic start up timer do one of the following;  
1. Start the vehicle manually with the use of the ignition key and depress the  
brake pedal.  
2. Remote start the vehicle using your keychain RF transmitter.  
NOTE: Option button used in combination is only available on the alternate re-  
mote transmitter and not available on the LCD Transmitter.  
ADDITIONAL REMOTE FUNCTION (CHANNEL 3)  
This system has an additional feature that can be connected to a number of  
different optional accessories. Some of the more common uses for this channel  
are:  
 Remote Trunk Release  
 Remote Window Closure  
 Remote Garage Door Interface  
To activate the optional accessory, press and hold the trunk/key button on the  
keychain transmitter for four seconds.  
NOTE: The feature that has been added to channel 3 will always be activated  
using the same transmitter button that remotely starts the vehicle. There  
is no way to move the channel 3 function to a different transmitter button.  
ADDITIONAL REMOTE FUNCTION (CHANNEL 4)  
This system has an additional feature that can be connected to a number of  
different optional accessories. Some of the more common uses for this channel  
are:  
Can Be Set Up To Activate Rear Window Defogger During  
Remote Start If Vehicle Is So Equipped  
Remote Window Closure  
Rear Hatch Release  
Right Or Left Slider Doors in An Equipped Van  
To activate the optional accessory, press the option button on the keychain  
transmitter. The optional accessory will immediately engage.  
ADDITIONAL REMOTE FUNCTION (CHANNEL 5)  
This system has an additional feature that can be connected to a number of  
different optional accessories. Some of the more common uses for this channel  
are:  
Remote Trunk Release  
Remote Window Closure  
Rear Hatch Release  
Right Or Left Slider Doors in An Equipped Van  
To activate the optional accessory, press the option button on the keychain  
transmitter. The optional accessory will immediately engage.  
ADDITIONAL REMOTE FUNCTION (CHANNEL 6)  
This system has an additional feature that can be connected to a number of  
different optional accessories. Some of the more common uses for this channel  
are:  
Rear Hatch Release  
Page 12  
128-8842  
12 of 20  
 
Right Or Left Slider Doors in An Equipped Van  
Driver Priority Settings In Vehicles So Equipped  
To activate the optional accessory, press the option button on the keychain  
transmitter. The optional accessory will immediately engage.  
ADDITIONAL REMOTE FUNCTION (CHANNEL 7)  
This system has an additional feature that can be connected to a number of differ-  
ent optional accessories. Some of the more common uses for this channel are:  
Rear Hatch Release  
Right Or Left Slider Doors in An Equipped Van  
Driver Priority Settings In Vehicles So Equipped  
Second Driver Priority Settings In Vehicles So Equipped  
To activate the optional accessory, press the option button on the keychain  
transmitter. The optional accessory will immediately engage.  
NOTE: If your system utilizes the transmitter shown, the second option button  
may be configured to operate additional accessories. Please consult your  
installing retailer for more information concerning the options available.  
TURBO TIMER MODE  
This system provides a means to cool down the vehicles turbo charger, if so  
equipped, by allowing the vehicle to continue to run for a prescribed period of time  
every time the vehicle's engine is turned off. This feature requires the system to be  
set up for turbo timer during installation. Consult with your installation center to be  
certain this feature was activated and how long the vehicle will continue to run, 3, 5,  
or 10 minutes after the ignition switch is turned off.  
To activate the turbo timer:  
Anytime the ignition key is in the on position for more than 15 seconds:  
1) Place the gear selector in park.  
2) Set the parking, (hand), brake.  
3) Be certain your foot is off the brake pedal.  
4) Press the receiver's program/Push-Button switch 2 times within 5 seconds.  
The parking lights will flash two times indicating the mode was successfully en-  
tered. If your parking lights flashed four times, this indicates the turbo mode was  
on and is now turned off.  
With the turbo timer mode selected on, after you've arrived at your destination,  
while the engine is still running, set the parking brake, pause 2 seconds, then turn  
the ignition switch to the off position. The engine will continue to run the allotted  
time according to the selection during installation.  
If you do not want the vehicle to continue to run for one cycle, simply step on the  
vehicle's brake, or release the parking brake, or activate the transmitter's start  
button two times in succession. Any of these will cause the engine to turn off.  
TELEMATICUPGRADE:  
This system has the ability to have a telematic upgrade module connected to it.  
This is a upgrade that can give you control of certain functions of your vehicle from  
a Telephone, or in some cases a computer interface. Please check with your  
installation center for most recent Telematic Upgrades. If you had a Telematic  
Upgrade installed, the manual supplied with the upgrade unit will provide a opera-  
tors manual advising of the features of the system and means available to control  
these features of your vehicle.  
Page 13  
128-8842  
13 of 20  
 
TRANSCEIVER ICONSAND THEIR INDICATIONS  
When Disarmed, Press the Arm/Lock button to Lock and Arm  
the System. The Lock Icon is displayed on the LCD panel & the  
parking lights flash once.  
When Armed, Press the Disarm/Unlock button to  
Unlock and Disarm the System. The Unlock Icon is displayed  
on the LCD panel & the parking lights flash twice.  
When the Key Icon Button Has Been Operated for 3 seconds  
the trunk open icon will flash on the LED Screen. If text mode  
was selected, the words Trunk Open will appear and remain  
on the screen until the trunk is shut.  
When the Key Icon Button is pressed 2 times in succession  
The three puffs of smoke are displayed on the LCD screen  
while the vehicle is running. The exhaust indication will flash  
and the hour glass will indicate count down timer based on the  
5, 10, 15, or 20 minute run time set up by your installation cen-  
ter. When the unit shuts off the exhaust indication will turn off  
and the transmitter will play a melody.  
NOTE: Engine can be started in many modes armed, disarmed,  
valet, etc... The screen shown is Locked/Armed and running.  
When the Panic Mode has been activated and the  
system is armed the vehicle's lights will flash, the  
siren and lock icon will be displayed on the LCD  
screen and the siren will beep. If the system is  
disarmed and the Panic Mode is activated, the  
lights will flash unlock icon will be displayed and  
the siren will beep on the LCD screen.  
When ever the vehicle is operated from the two way transmitter, the  
unit will beep responsive to the function executed at the vehicle. 1  
beep when armed, 2 beeps when disarmed, etc... at times It may  
be inconvenient or too noisy to hear the beep tones, so the system  
allows you to set the unit for vibrate mode. To toggle on or off beep  
tones/vibrate, Simultaneously press the "F" and unlock buttons.  
The icons shown left will appear in the upper left hand corner of the  
screen to indicate vibrate.If the alarm system has been triggered,  
the icon displayed on the transmitter LCD will indicate which zone  
has been activated, as well sound the beep tones, or vibrate  
dependent upon the setting as shown above. The following trigger  
patterns will be displayed.  
Triggered and the entry attempt was made to one of the  
vehicle Doors.  
Triggered and entry attempt was made to the vehicles Hood  
Page 14  
128-8842  
14 of 20  
 
or Trunk.  
Triggered and entry attempt was made to the vehicles glass, or  
the vehicle has been hit or bumped hard enough to cause a  
response from the vibration detector.  
ADDITIONAL ICONS THAT MAYBE DISPLAYEDARE:  
If the arm/disarm chirp tones have been turned off at the vehicle,  
when you arm, or disarm, the display will indicate this as shown  
and there will be no arm/disarm chirps at the transmitter. This is  
true if the transmitter is set for vibrate mode.  
When the vehicle is armed, and a door is opened, or ajar, the transmitter will chirp  
3 times, the lights will flash, and the display will indicate a door trigger as shown  
on the previous page. When the door is closed or the zone clears, the transmitter  
will chirp 1 time, and the display will clear.  
When the vehicle is armed, and the hood or trunk, is opened or ajar, the transmit-  
ter will chirp 3 times, the lights will flash, and the display will indicate a hood or  
trunk trigger as shown on the previous page. When the hood or trunk is closed, or  
the zone clears, the transmitter will chirp 1 time, and the display will clear.  
NOTE: The Extended range transmitter(s) will only achieve the maximum  
operating range when communicating with the system in ideal operating  
conditions. Normally occurring environmental factors such as buildings, trees,  
terrain and weather or interference from other radio or electrical equip-  
ment may have adverse effects on the extended range transmitters  
affecting operating range. Reductions in the maximum operating range,  
are not indicative of a fault condition.  
PROGRAMMED TRANSMITTER NOTIFICATION (PTN)  
Every time after Disarm when the ignition key is turned on, the unit's LED will  
report the number of transmitters programmed into the system. This safety  
feature will alert you if an unauthorized transmitter has been programmed into  
your vehicle's security system without your knowledge. Typical from the factory,  
there will be a 2 flash, pause, repeated 3 times indicating that two transmitters  
are programmed into the system. If you note additional flashes, there may  
heve been an additional transmitter added without your knowledge or authori-  
zation. If you notice a change in the transmitter LED report pattern, you can  
correct this by looking up how to erase and reprogram your transmitters found  
in the transmitter programming guide. This reprogram operation will erase all  
unauthorized or unwanted transmitters.  
Page 15  
128-8842  
15 of 20  
 
ADDITIONALREMOTE FEATURES:  
The two way remote control unit allows you to access status  
information from the vehicle, check temperature, light the  
display, toggle the transmitter from beep tones to vibrate mode,  
initiate daily start timer, and temperature start. Selection of these  
and other features are shown below:  
NOTE: Transmitter must be within operating range of the  
vehicle, approximately 1000 ft.  
Check Vehicle Status:  
Press the lock+key+option buttons simultaneously for 1 second.  
The vehicle's alarm will display the systems current status.  
Check Temperature: (Only available on certain remote start units)  
Press the option+key buttons simultaneously for 1 second. The  
vehicle's alarm will display the temperature. Temperature is  
read from the alarm's module located below the dashboard.  
This reading may be higher than actual ambient temperature due to the  
greenhouse and is relative only to the inside vehicle temperature.  
Temperature Start Mode: (Available on certain models)  
To toggle this feature on or off, from the armed mode, press the Option &  
Unlock Buttons simultaneously, the temperature icon appear on, or  
disappear from the display, and the transmitter will emit a tone.  
NOTE: This feature must be active in the feature selection menu of your  
system. Check with your installing dealer to insure this feature is  
set to the on position.  
Light The Display:  
Press and release the "F" (Function) button one time. The display will illumi-  
nate for 10 seconds.  
Vibrate Or Tones:  
Press the "F" and unlock buttons simultaneously to toggle this feature on and  
off.  
Daily Start Timer: (Only available on certain remote start units)  
Press the option+lock buttons simultaneously for 1 second. The  
transmitter will beep and display the 24hr timer. The vehicle will start  
automatically when the time set is reached. (See chart for time settings).  
Pressing this button combination a second time will toggle this feature  
off. Note the transmitter must be within range of the vehicle to set this feature  
and within range to cause the vehicle to start at the preset time. The unit will  
start at the prescribed time once only. This function must be selected each time  
you want the vehicle to start. To activate this function, (a) Turn the ignition switch  
off. (b) Within 10 seconds of step (a), depress and hold the brake pedal, while  
pressing the key icon transmitter button 2 times. (c) the unit will emit 2 chirps,  
the transmitter will beep and the start timer icon on the display will remain on.  
NOTE: This feature must be activated at the vehicle at the prescribed time. Once  
activated at the vehicle, you can toggle the feature on simultaneously pressing  
the Lock + Option buttons of the transmitter. The 24 hour icon will appear and  
the transmitter will emit a tone confirming the feature is active.  
Page 16  
128-8842  
16 of 20  
 
NOTE: The unit will start once and run for the prescribed time. If you require  
more frequent starting please refer to auto start up timer mode shown earlier in  
this guide.  
NOTE: To insure accurate 24 Hour Start up, it is advisable to reset the start time  
periodically as time may drift slightly each day.  
Timing Count Down:  
The unit offers an additional count down timer for situations where an  
alert tone may be needed to remind you of something important. For  
instance you may have a meeting 4 hours from now and you want a  
reminder in 3 Hrs and 45 Mins. This additional count down timer allows  
you to set the count down up 19 Hours and 59 Minutes from the current  
time and when the timer reaches zero, the transmitter will emit a tone or vibrate  
dependent on your preferred setting. See chart for setting the count down time  
for this feature.  
Valet:  
When the System is in the valet mode, the icon shown will show  
in the display when the status check buttons are activated.  
Parking Meter Counter:  
The transmitter has a built in clock that can count down from 10, 20, 30, 60, 90,  
or 120 minutes. This feature is useful when parking the vehicle in a metered  
parking lot. If the time on the parking meter is 30 minutes, you can set the  
count down timer to 20 minutes. The transmitter will emit a beep tone when  
the timer expires to remind you to get back to your vehicle. See following chart  
for setting the parking meter count down timer feature.  
Alarm Clock Mode:  
The transmitter has a built in alarm clock that can be set to beep at a certain  
time each day. The alarm clock mode must be set, and the feature  
turned on. To use this feature please refer to the chart on the  
following page.  
NOTE: Your system is shipped with two transmitters, 1 two way,  
shown on the left and the one way transmitter, shown right. The one  
and two way transmitters are programmed from the factory with  
separate lock & unlock buttons, the trunk/key icon button operates  
remote start and remote trunk release where applicable. The  
option button and any button combination may be programmed to  
operate various options. Consult your installation center  
for button programming and options that may have been  
added to your vehicle. Although this is the default  
programming from the factory, this can be changed for  
you to any configuration you prefer. Please refer to the  
transmitter program guides included with your kit.  
NOTE: A maximum of two of either style transmitter may  
be programmed to your unit.  
Page 17  
128-8842  
17 of 20  
 
Battery Indicator: Your transmitter has a battery indicator that is shown in  
the lower left corner of the screen as shown left. This icon indicates a  
charged battery shown with 3 bars. As the battery discharges, the  
bars will disappear. 1 bar indicates the battery needs charging.  
Connect the USB charger supplied with your unit and bring to full charge.  
Other icons that will be displayed at times when certain functions and  
features are active in the vehicle or on the remote:  
Range Indicator. The range indicator will have bars to the side of  
the icon if the unit is out of range.  
Vibrate Mode On, this icon will be displayed if you select vibrate  
instead of tones. To toggle vibrate on and off, press "F" + Unlock  
simultaneously.  
Alarm Clock. This icon will be toggled on and off when the "F" +  
Trunk/Key buttons are pressed simultaneously. The feature must be  
set in the feature selection menu of the transmitter.  
Timing Count Down:  
The unit offers an additional count down timer for situations where an  
alert tone may be needed to remind you of something important. Setting  
information shown on previous page.  
Power Save Feature. Press the "F" and Lock buttons simulta-  
neously to toggle this feature on and off. With this mode on, the  
battery in the transmitter will go into a power down mode when the  
unit is disarmed.  
24 Hour Start Timer. This icon is displayed when the 24 hour start  
timer is activated. Press the option+lock buttons simultaneously for 3  
second. The transmitter will beep and display the 24hr timer. The  
vehicle will start automatically when the time set is reached. (See chart for  
time settings). Pressing this button combination a second time will toggle  
this feature off. Note the transmitter must be within range of the vehicle to  
set this feature and within range to cause the vehicle to start at the preset  
time. The unit will start at the prescribed time once only. This function  
must be selected each time you want the vehicle to start. To activate this  
function, (a) Turn the ignition switch off. (b) Within 10 seconds of step (a),  
depress and hold the brake pedal, while pressing the key icon transmitter  
button 2 times. (c) the unit will emit 2 chirps, the transmitter will beep and  
the start timer icon on the display will remain on.  
Temperature Start Mode. This icon will appear when the temp start  
mode is activated. The vehicle will start one time automatically when the  
temperature reaches 0*. Caution, Be certain vehicle is outside before  
activating this mode. To toggle this feature on of off, from the Locked/  
Armed mode, press the Option and Lock buttons simultaneously.  
(Available on certain remote start models only).  
Throughout this manual you will find screen shots where they apply if  
using the two way transmitter. If using the one way transmitter while the  
two way transmitter is within range of the vehicle, the two way transmitter  
will update it's screen.  
Page 18  
128-8842  
18 of 20  
 
Page 19  
128-8842  
19 of 20  
 
SS9000  
SYSTEM FUNCTIONS ATAGLANCE  
LED INDICATOR  
RAPID FLASHING  
SLOW FLASHING  
=
=
=
=
=
=
=
=
PASSIVEARM OR REARMING  
ARMED  
DISARMED  
VALET MODE  
REMOTE START OVERRIDE  
INTRUSION ZONE 3  
INTRUSION ZONE 2  
INTRUSION ZONE 1  
OFF  
ON SOLID  
2 SHORT,,, 1LONG  
3 FLASH,,, PAUSE  
2 FLASH,,, PAUSE  
1 FLASH,,, PAUSE  
SIREN CHIRP INDICATIONS  
1 CHIRP*  
=
=
=
=
ARM  
DISARM  
ARM W/ENTRY POINT OPEN  
DISARM W/INTRUSION  
2 CHIRPS*  
3 CHIRPS  
4 CHIRPS  
* These chirps are optional and can be selected off.  
PARKING LAMP INDICATORS  
1 FLASH  
2 FLASHES  
3 FLASHES  
=
=
=
ARM  
DISARM  
DISARM / INTRUSION  
© 2010 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788  
Page 20  
128-8842  
128-8842  
20 of 20  
 

3M Projector DX701i User Manual
Accusplit Watch A740MXT User Manual
Acer Computer Monitor UMVV6AAC01 User Manual
ACTiSYS Network Card ACT 100M User Manual
ADC Switch 103326AE User Manual
Alto Shaam Convection Oven AR 7H User Manual
Atlona TV Cables ATP 14009 User Manual
Avocent Switch KVM Switching User Manual
Banner Stud Sensor MINI BEAM Expert User Manual
Beko Planer DRCS 76 S User Manual