Avocent Switch SC8 DVI User Manual

The Power of Being There®  
Quick Installation Guide  
®
®
Cybex SwitchView  
SC8 DVI Switch  
The following instructions will help you  
install your SwitchView SC8 DVI switch.  
Should you require further assistance, please  
contact Avocent Technical Support.  
To install the Cybex SwitchView SC8 DVI switch  
4
2
Connecting local peripherals  
1
Power down all servers that will be part of your  
SwitchView SC8 DVI switching system. Locate  
your PS/2 keyboard, DVI monitors and PS/2  
mouse. Plug your DVI monitor cables into the  
CONSOLE ports on the left side of the back  
of your switch. Plug your PS/2 keyboard cable  
and your PS/2 mouse cable into the keyboard  
and mouse ports respectively.  
CONSOLE  
H
G
F
E
D
C
B
A
Optional  
RF ground  
(not required  
for safety)  
1
Connecting your servers  
2
Locate your first cable set consisting of two  
PS/2 cables and one or two DVI cables. The  
SwitchView SC8 DVI switching system has  
eight port sets labeled A-H on the rear of the  
unit. Plug the two PS/2 cables (keyboard  
and mouse) and the DVI cable (monitors)  
into the corresponding ports on your server.  
Plug the other ends into any available server port  
setonyourSwitchViewSC8DVIswitchingsystem.  
Repeat this process until all servers are properly  
attached to the SwitchView SC8 DVI switch.  
3
Input Power: 60 W; Operating Voltage 100-240 VAC  
Power Frequency: 50-60 Hz  
Switching your servers  
4
Press the appropriate front panel button labeled A-H to  
Supported Hardware  
access servers in your SwitchView switching system.  
Server: IBM, PC/AT, PS/2 and 100% compatibles  
Video Modes: VGA, SVGA, XGA, SXGA, UXGA,  
HDTV and QXGA  
LEDs  
Turning on your system  
3
Each target port (A-H)has dual LEDs on the front panel. A  
greenLEDindicatesthetargetdeviceisonandconnected  
to the switch. An amber LED indicates the target device  
is selected (KVM session).  
Loc ate the power cord that c ame with your switch.  
Plug one end into the IEC power connector on  
theSwitchViewswitch.Ensurethepowerswitch  
is off, then plug the other end of the power cord  
into an AC wall outlet. Turn on your switch first,  
then turn on all attached servers.  
Maximum Resolution: 2048 x 1536 @ 75Hz  
Peripherals: PS/2 keyboard, PS/2 mouse and  
IntelliMouse (PS/2 only)  
Environmental  
Mechanical  
Operating Temperature: 41˚ (5˚C) to 104˚ (40˚C)  
Storage Temperature: -4˚ (-20˚C) to 122˚ (50˚C)  
H x W x D = 3.6” x 17.2” x 10.8” (9.1 x 43.7 x 27.4 cm)  
Weight = 9.5 lbs (4.3 kg)  
To Contact Avocent Technical Support: Visit www.avocent.com/support  
Avocent, the Avocent logo, The Power of Being There, Cybex and SwitchView are registered trademarks of Avocent Corporation or its affiliates. ©2007 Avocent Corporation. All rights reserved.  
 
590-502-501D  

Advanced Global Technology Digital Camera QSP 660 User Manual
Agilent Technologies Network Router E4400 60230 User Manual
Alamo Lawn Mower 00785503C User Manual
Altec Lansing Portable Speaker 403A User Manual
Alvin High Chair CE101 User Manual
AMC Home Theater System XN 11n User Manual
Ask Proxima Projector AV 9350 User Manual
Ativa Calculator PET1030 User Manual
Bakers Pride Oven Oven BK 18 User Manual
Beko Air Conditioner LG BKE4500 D LG BKE5505 D User Manual