Beko Clothes Dryer DCY 7202 XW3 User Manual

Dryer  
DCY 7202 XW3  
User Manual  
2960311039_EN/220115.1711  
 
1 Important instructions for safety and  
environment  
This section contains safety instructions that will help protect from risk of  
personal injury or property damage. Failure to follow these instructions shall  
void any warranty.  
1.1 General safety  
The dryer can be used by children at and above 8 years old and by  
persons whose physical, sensory or mental capabilities were not fully  
developed or who lack experience and knowledge provided that they  
are supervised or trained on the safe usage of the product and the risks  
it brings out. Children should not play with the product. Cleaning and  
maintenance works should not be performed by children unless they are  
supervised by someone.  
Children of less than 3 years should be kept away unless continously  
supervised.  
Adjustable feet should not be removed. The gap between the dryer and  
the floor should not be reduced with materials such as carpet, wood and  
tape. This will cause problems with the dryer.  
Always have the installation and repairing procedures carried out by the  
Authorized Service. Manufacturer shall not be held liable for damages  
that may arise from procedures carried out by unauthorized persons.  
Never wash the dryer by spraying or pouring water onto it! There is the  
risk of electric shock!  
 
Dryer / User Manual  
3 / 28 EN  
Important instructions for safety and environment  
1.1.1 Electrical safety  
A Electrical safety instructions should be followed while electrical  
connection is made during the installation.  
Connect the dryer to a grounded outlet protected by a fuse at the value  
specified on the type label. Have the grounding installation performed by  
a qualified electrician. Our company shall not be liable for any damages  
that will arise when the dryer is used without grounding in accordance  
with the local regulations.  
The voltage and allowed fuse protection is stated on the type label plate.  
The voltage specified on the type label must be equal to your mains  
voltage.  
Unplug the dryer when it is not in use.  
Unplug the dryer from the mains during installation, maintenance,  
cleaning and repair works.  
Do not touch the plug with wet hands! Never unplug by pulling on the  
cable, always pull out by grabbing the plug.  
Do not use extension cords, multi-plugs or adaptors to connect the dryer  
to power supply in order to decrease the risk of fire and electric shock.  
Power cable plug must be easily accessible after installation.  
B Damaged mains cable should be changed notifying the Authorized  
B If the dryer is faulty, it must not be operated unless it is repaired  
Service.  
by an authorized service agent! There is the risk of electric shock!  
 
Dryer / User Manual  
4 / 28 EN  
Important instructions for safety and environment  
1.1.2 Product safety  
Points to be taken into consideration for fire hazard:  
Below specified laundry or items must not be dried  
in the dryer considering fire hazard.  
Unwashed laundry items  
Items soiled with oil, acetone, alcohol, fuel oil, kerosene, stain  
removers, turpentine, paraffin or paraffin removers must be  
washed in hot water with plenty of detergent before being dried  
in the dryer.  
For this reason especially the items containing the above  
specified  
stains must be washed very well, to do this  
use adequate detergent and choose a high washing  
temperature.  
Below specified laundry or items must not be dried in the  
dryer due to the fire hazard:  
Garments or pillows bolstered with rubber foam (latex foam),  
shower bonnets, water resistant textiles, materials with rubber  
reinforcement and rubber foam pads.  
Clothing cleaned with industrial chemicals.  
Items such as lighter, match, coins, metal parts, needle etc.  
may damage the drum set or may lead to functional problems.  
Therefore check all the laundry that you will load into your dryer.  
Never stop your dryer before  
the programme completes. If you must do this, remove all  
laundry  
quickly and lay them out to dissipate the heat.  
Clothes that are washed inadequately may ignite on their own  
and even may ignite after drying ends.  
 
Dryer / User Manual  
5 / 28 EN  
Important instructions for safety and environment  
You must provide enough ventilation in order to prevent gases exiting from  
devices operating with other types of fuels including the naked flame from  
accumulating in the room due to the back fire effect.  
Underwear that contains metal reinforcements should not be  
A
dried  
in the dryer. Dryer may be damaged if metal reinforcements come  
loose and break off during drying.  
Use softeners and similar products in accordance with the  
instructions of their manufacturers.  
C
C
Always clean the lint filter before or after each loading. Never  
operate the dryer without the lint filter installed.  
Never attempt to repair the dryer by yourself. Do not perform any repair  
or replacement procedures on the product even if you know or have the  
ability to perform the required procedure unless it is clearly suggested in  
the operating instructions or the published service manual. Otherwise, you  
will be putting your life and others’ lives in danger.  
There must not be a lockable, sliding or hinged door that may block  
the opening of the loading door in the place where your dryer is to be  
installed.  
Install your dryer at places suitable for home use. (Bathroom, closed  
balcony, garage etc.)  
Make sure that pets do not enter the dryer. Check the inside of the dryer  
before operating it.  
Do not lean on the loading door of your dryer when it is open, otherwise it  
may fall over.  
The lint must not be allowed to accumulate around the tumble dryer  
 
Dryer / User Manual  
6 / 28 EN  
Important instructions for safety and environment  
1.2 Mounting over a washing machine  
A fixing device should be used between the two machines when installing  
the dryer above a washing machine. The fitting device must be installed  
by the authorized service agent.  
Total weight of the washing machine and the dryer -with full load- when  
they are placed on top of each other reaches to approx. 180 kilograms.  
Place the products on a solid floor that has sufficient load carrying  
capacity!  
Washing machine cannot be placed on the dryer. Pay attention  
to the above warnings during the installation on your washing  
A machine.  
Installation Table for Washing Machine and Dryer  
Washing Machine Depth  
Dryer Depth  
62cm 60 cm 54 cm 50 cm 49 cm 45 cm 40 cm  
Can be  
Can be  
Can be  
Can be  
Can be  
Can be Cannot be  
54 cm  
60 cm  
installed installed installed installed installed installed installed  
Can be  
Can be  
Can be  
Can be  
Can be Cannot be Cannot be  
installed installed installed installed installed installed installed  
 
Dryer / User Manual  
7 / 28 EN  
Important instructions for safety and environment  
1.3 Intended use  
Dryer has been designed for domestic use. It is not suitable for  
commercial use and it must not be used out of its intended use.  
Use the dryer only for drying laundry that are marked accordingly.  
The manufacturer waives any responsibility arisen from incorrect usage or  
transportation.  
The service life of the dryer that you purchased is 10 years. During this  
period, original spare parts will be available to operate the dryer properly.  
1.4 Child safety  
Packaging materials are dangerous for the children. Keep packaging  
materials away from children.  
Electrical products are dangerous for the children. Keep children away  
from the product when it is operating. Do not let them tamper with the  
dryer. Use the child-proof lock in order to prevent the children to tamper  
with the dryer.  
Child-proof lock is on the control panel. (See Child lock)  
C
Keep loading door closed even when the dryer is not in use.  
 
Dryer / User Manual  
8 / 28 EN  
Important instructions for safety and environment  
1.5 Compliance with the WEEE regulation  
and disposing of the waste product  
This product complies with EU WEEE Directive (2012/19/EU). This  
product bears a classification symbol for waste electrical and  
electronic equipment (WEEE).  
This product has been manufactured with high quality parts and  
materials which can be reused and are suitable for recycling. Do  
not dispose of the waste product with normal domestic and other  
wastes at the end of its service life. Take it to the collection center for the  
recycling of electrical and electronic equipment. Please consult your local  
authorities to learn about these collection centers.  
1.6 Compliance with RoHS Directive:  
The product you have purchased complies with EU RoHS Directive  
(2011/65/EU). It does not contain harmful and prohibited materials  
specified in the Directive.  
1.7 Package information  
Packaging materials of the product are manufactured from recyclable  
materials in accordance with our National Environment Regulations. Do  
not dispose of the packaging materials together with the domestic or other  
wastes. Take them to the packaging material collection points designated  
by the local authorities.  
Please visit the following website to get more information on the product.  
 
Dryer / User Manual  
9 / 28 EN  
Important instructions for safety and environment  
1.8 Technical Specifications  
EN  
Height (Min. / Max.)  
Width  
Depth  
84,6 cm / 86,6 cm*  
59,5 cm  
54 cm  
7 kg**  
36 kg  
Capacity (max.)  
Net weight (plastic front door usage)  
Net weight (glass front door usage)  
Voltage  
38 kg  
Rated power input  
Model code  
See type label***  
* Min. height: Height with adjustable feet are closed.  
Max. height: Height with adjustable feet are opened maximum.  
** Dry laundry weight before washing.  
*** Type label is located behind the loading door.  
Technical specifications of the dryer are subject to specification  
without notice to improve the quality of the product.  
Figures in this manual are schematic and may not match the  
product exactly.  
Values stated on markers on the dryer or in the other published  
documentation accompanying with the dryer are obtained in  
laboratory in accordance with the relevant standards. Depending  
on operational and environmental conditions of the dryer, these  
values may vary.  
C
C
C
 
Dryer / User Manual  
10 / 28 EN  
2 Your Dryer  
2.1 Package Contents  
1
2
3
4
5
1. Water drain hose *  
2. Filter drawer spare sponge*  
3. User Manual  
4. Drying basket*  
5. Drying basket user manual*  
*It can be supplied with your machine depending on its model.  
 
Dryer / User Manual  
11 / 28 EN  
3 Installation  
3.2 Removing the transportation  
safety assembly  
Before the calling the nearest Authorized Service for the  
installation of the dryer, ensure that electrical installation  
and water drain is appropriate referring to the user's  
manual.(See 3.3 Connecting to the drain and 3.5  
Electrical connection) If they are not suitable, contact  
a qualified electrician and technician to make necessary  
arrangements.  
Remove the transportation safety  
assembly before using the dryer for the  
first time.  
A
Open the loading door.  
There is a nylon bag inside the drum that contains a  
piece of styrofoam. Hold it from its section marked with  
XX XX.  
Preparation of the dryer's location  
as well as the electrical and waste  
water installations is under customer's  
C
Pull the nylon towards yourself and remove the  
transportation safety assembly.  
responsibility.  
Prior to installation, visually check if the  
dryer has any defects on it. If the drier  
A is damaged, do not have it installed.  
Damaged products cause risks for your  
safety.  
3.1 Appropriate installation location  
Install the dryer on a stable and level surface.  
Dryer is heavy. Do not move it by yourself.  
Operate your dryer in a well ventilated, dust-free  
environment.  
The gap between the dryer and the surface should  
not be reduced by the materials such as carpet,  
wood and tape.  
Do not cover the ventilation grills of the dryer.  
There must not be a lockable, sliding or hinged  
door that may block the opening of the loading  
door in the place where your dryer is to be  
installed.  
Once the dryer is installed, it should stay at the  
same place where its connections have been  
made. When installing the dryer, make sure that  
its rear wall does not touch anywhere (tap, socket,  
etc.).  
Place the dryer at least 1 cm away from the edges  
of other furniture.  
Your dryer can be operated at temperatures  
between +5°C and +35°C. If the operating  
conditions fall outside of this range, operation of  
the dryer will be adversely affected and it can get  
damaged.  
The rear surface of the tumble dryer shall be  
placed against a wall.  
Check that no part of the transportation  
safety assembly remains inside the drum.  
A
3.3 Connecting to the drain  
In products equipped with condenser unit, water  
accumulates in the water tank during the drying cycle.  
You should drain accumulated water after each drying  
cycle.  
You can directly drain accumulated water through the  
water drain hose supplied with the product instead of  
periodically draining the water collected in the water  
tank.  
Connecting the water drain hose  
1-2 Pull hose at the behind of the dryer by hand in  
order to disconnect it from where it is connected.  
Do not use any tools to remove the hose.  
3
Connect one end of the drain hose supplied with  
the dryer to the connection point from where you  
removed the hose of the product in previous step.  
4
Connect the other end of the drain hose directly to  
the wastewater drain or to the washbasin.  
Do not place the dryer on the power  
cable.  
B
 
Dryer / User Manual  
12 / 28 EN  
Installation  
3.5 Electrical connection  
For specific instructions for electrical connection  
required during installation (see 1.1.1 Electrical  
Safety)  
1
2
4
3.6 Transportation of the dryer  
Unplug the dryer before transporting it.  
Drain all water that has remained in the dryer.  
If direct water drain connection is made, then remove  
the hose connections.  
3
We recommend carrying the dryer in  
upright position. If it is not possible to  
carry the machine in the upright position,  
we recommend carrying it by tilting  
A
towards the right side when looked from  
the front.  
Hose connection should be made in a safe  
manner. Your drain house will be flooded if  
the hose comes out of its housing during  
water discharge.  
3.7 Changing the illumination lamp  
In case an illumination lamp is used in your laundry  
dryer.To change the Bulb/LED used for illumination of  
your tumble dryer, call your Authorized Service.  
The lamp(s) used in this appliance is not suitable for  
household room illumination. The intended purpose of  
this lamp is to assist the user to place laundry in the  
tumble dryer in a comfortable way.  
A
Water drain hose should be attached to a  
height of maximum 80 cm.  
C
C
Make sure that the water drain hose is not  
stepped on and it is not folded between the  
drain and the machine.  
3.4 Adjusting the feet  
In order to ensure that the dryer operates more silently  
and vibration-free, it must stand level and balanced on  
its feet. Balance the machine by adjusting the feet.  
Turn the feet to left or right until the dryer stands level  
and firmly.  
Never unscrew the adjustable feet from  
their housings.  
C
 
Dryer / User Manual  
13 / 28 EN  
4 Preparation  
4.1 Laundry suitable for drying in the dryer  
Always obey the instructions given on the garment tags. Dry only the laundry having a label stating that they are  
suitable for drying in a dryer and make sure that you select the appropriate programme.  
LAUNDRY DRYING SYMBOLS  
Drying  
Symbols  
Suitable for  
dryer  
No Iron  
Do not dry-  
clean  
Sensitive /  
Delicate dry  
Do not dry  
with dryer  
Do not dry  
Drying  
Settings  
Iron -  
Iron at high  
temperature  
Iron at medium  
temperature  
Iron at low  
temperature  
Dry or Steam  
IRON  
200 0C  
150 0C  
110 0C  
Maximum temperature  
4.2 Laundry not suitable for drying in 4.4 Things to be done for energy  
the dryer  
saving  
Following information will help you use the dryer in an  
ecological and energy-efficient manner.  
Delicate embroidered fabrics, woolen, silk  
garments, delicate and valuable fabrics,  
airtight items and tulle curtains are not  
suitable for machine drying.  
Spin your laundry at the highest speed possible  
when washing them. Thus, the drying time is  
shortened and energy consumption is reduced.  
Sort out the laundry depending on their type and  
thickness. Dry the same type of laundry together.  
For example thin kitchen towels and table clothes  
dries earlier than thick bathroom towels.  
Follow the instructions in the user manual for  
programme selection.  
C
4.3 Preparing laundry for drying  
Laundry may be tangled with each other after  
washing. Separate the laundry items before  
placing them into the dryer.  
Dry garments having metal accessories such as  
zippers, inside out.  
Fasten the zippers, hooks and buckles and button  
sheets.  
Do not open the loading door of the machine  
during drying unless necessary. If you must  
certainly open the loading door, do not to keep it  
open for a long time.  
Do not add wet laundry while the dryer is in  
operation  
Clean the lint filter before or after each drying  
cycle. (See 6.1 in Maintenance and cleaning)  
 
Dryer / User Manual  
14 / 28 EN  
Preparation  
Clean the condenser regularly at least once every  
month or after every 30 drying cycles. (See 6.4 in  
Maintenance and cleaning)  
Ventilate the room, where the dryer is located, well  
during drying.  
It is not recommended to load the dryer  
with laundry exceeding the level indicated  
in the figure. Drying performance will  
degrade when the machine is overloaded.  
Furthermore, dryer and the laundry can get  
damaged.  
C
4.5 Correct load capacity  
Following weights are given as examples.  
Follow the instructions in the “Programme selection and  
consumption table”. Do not load more than the capacity  
values stated in the table.  
Approximate weights  
Laundry  
(g)*  
1500  
1000  
500  
350  
700  
250  
100  
700  
350  
150  
300  
200  
500  
350  
700  
100  
125  
Cotton quit covers (double)  
Cotton quit covers (single)  
Bed sheets (double)  
Bed sheets (single)  
Large tablecloths  
Small tablecloths  
Tea napkins  
Bath towels  
Hand towels  
Blouses  
Cotton shirts  
Shirts  
Cotton dresses  
Dresses  
Jeans  
Handkerchiefs (10 pieces)  
T-Shirts  
*Dry laundry weight before washing.  
 
Dryer / User Manual  
15 / 28 EN  
5 Operating the product  
5.1 Control panel  
1
4
3
2
1. On/Off/Program selection button  
2. Start/Pause button  
3. Delay time button  
4. Audio alarm level button  
5.2 Screen symbols  
Iron dry  
Freshen End/anti-  
Cupboard Cupboard  
Cottons Synthetics  
Extra  
Xpress  
Shirts  
Spin  
Timer  
Up  
creasing  
dry  
dry plus  
programs  
dry  
Child-proof  
lock  
Buzzer  
Mix  
On/Off  
Start  
pause  
cancel  
Tank  
full  
Dryness  
Level  
Filter  
cleaning  
Daily  
Jeans  
Timer Volume up  
Delay  
BabyProtect Sport  
Start/  
Wait/  
Ready  
Drying  
Mute  
Delicates  
 
Dryer / User Manual  
16 / 28 EN  
Operating the product  
When you select the desired program by using  
On/off/program selection button, the machine will  
5.3 Preparation of Tumble Dryer  
Plug in the tumble dryer.  
turn on.  
Open the loading door.  
Place the laundry into the tumble dryer without  
overloading.  
1
Push and close the loading door.  
Take care not to trap any laundry inside  
the loading door.  
A
4
3
2
Selection of program by using On/off/  
program selection button doesn’t mean  
that the program has been started.  
Press the Start/Pause button to start the  
program.  
C
5.4 Program selection  
There are 15 programs included in your tumble drier.  
1
4
3
2
Program selection and consumption table have  
been given in the order that might be mostly  
preferred by users.  
 
Dryer / User Manual  
17 / 28 EN  
Operating the product  
5.5 Program selection and consumption table  
Spin Speed  
Capacity in Washing  
Programs  
Program Description  
Drying Time (min)  
(kg)  
Machine  
(rpm)  
You may dry all your cotton laundry in this program. (T-shirt, pants,  
pyjamas, baby clothes, underwear, linen, etc.) You can put your  
laundry in the wardrobe without ironing.  
Cotton Cupboard dry  
7
1000  
1000  
116  
120  
You may use this program for extra dryness in thick laundry such as  
pants, tracksuit.  
Cotton Cupboard dry +  
7
You can put your laundry in the wardrobe without ironing.  
You may dry your cotton laundry to be ironed in this program to have  
them slightly damp for ease of ironing. (Shirt, T-shirt, tablecloth, etc.)  
Cotton Iron Dry  
Cotton Extra Dry  
7
7
1000  
1000  
90  
You may dry your thick cotton laundry in this program such as towels,  
bathrobe, etc. You can put your laundry in the wardrobe without  
ironing.  
124  
You may dry all your synthetic laundry in this program. (Shirt, T-shirt,  
underwear, tablecloth, etc.) You can put your laundry in the wardrobe  
without ironing.  
Synthetic Cupboard dry  
Synthetic Iron Dry  
3.5  
3.5  
800  
800  
45  
35  
You may dry your synthetic laundry to be ironed in this program to  
have them slightly damp for ease of ironing. (Shirt, T-shirt, tablecloth,  
etc.)  
Jeans  
Daily  
You may dry denim pants, skirts, shirts or jackets in this program.  
4
1200  
600  
80  
59  
You may dry both your cotton and synthetic daily laundry in this  
program.  
1.5  
It dries the shirts in a more sensitive manner, and causes less  
creasing and easier ironing.  
Shirt  
1.5  
4
1200  
1000  
40  
92  
You may dry your sports clothes that are appropriate for tumble drying  
in this program.  
Sport  
You may dry your delicate laundry or laundry with hand wash symbol  
(silk blouses, thin underwear, etc.) at low temperature in this program.  
Delicates  
2
-
600  
-
40  
10  
It just provides airing for 10 minutes without any hot air. You can air  
the cotton and linen laundry that are kept closed for a long time , and  
eliminate the odour in them.  
Freshen up  
You may select from time programs between 10 and 20 and 40  
minutes to achieve the desired drying level at low temperature. In this  
program, tumble drier’s operation lasts for the set time independently  
from the dryness of laundry.  
Timer programmes  
-
-
-
 
Dryer / User Manual  
18 / 28 EN  
Operating the product  
* : Energy Label standard program (EN 61121:2012) All the filters must be cleaned prior to test series.  
All values in the table have been specified as per the EN 61121:2012 standard. Consumption values may vary from  
the values in the table depending on the variances in laundry type, spin speed, ambient conditions, and voltage  
values.  
Energy consumption values  
Spin Speed in Washing  
Machine (rpm)  
Approximate residual Energy consumption  
Programs  
Capacity(kg)  
moisture content  
value (kWh)  
Cotton Wardrobe Dryness*  
Cotton Iron Dryness  
7
7
1000  
1000  
800  
60%  
60%  
40%  
4,17  
3,25  
1,42  
Synthetic Wardrobe Dryness  
3,5  
Power consumption of the off-mode for the standart cotton programme at full load, PO (W)  
Power consumption of the left-on mode for the standart cotton programme at full load, PL (W)  
0,5  
1,0  
„Cotton cupboard dry programme“ used at full and partial load is the standard drying programme  
to which the information in the label and the fiche relates, that this programme is suitable for drying  
normal wet cotton laundry and that it is the most efficient programme in terms of energy consumption  
for cotton.  
To obtain better results from your dryer, your laundry must be washed at suitable programs and spun at  
the recommended speed in the washing machine.  
C
C
There may be a little moisture on the shirts at the end of the programme. We recommend you not to  
leave the shirts in the dryer.  
 
Dryer / User Manual  
19 / 28 EN  
Operating the product  
5.6 Auxiliary functions  
Laundry may be added or removed during  
the delay time. At the end of countdown  
for Delay Time, Delay Time warning  
indicator turns off and drying starts.  
Audio alarm  
C
An audio alarm is heard when the program is completed  
in the tumble drier. If you do not want to hear the audio  
alarm, please press the “Audio Alarm” button. When you  
press the audio alarm button, the light turns on and you  
hear no alarm at the completion of program.  
Changing the delay time  
If you want to change the time during countdown:  
Cancel the program by turning On/off/program  
selection button. Repeat the Delay time selection  
process after selecting the desired program.  
You may select this function before or  
after the program starts.  
C
Cancelling the delay time function  
If you want to cancel the delay time countdown and start  
the program immediately:  
5.7 Warning indicators  
Cancel the program by turning On/off/program  
selection button. Press the “Start/Pause” button  
after selecting the desired program.  
Warning indicators may vary depending  
on the model of your tumble drier.  
C
Filter cleaning  
The warning indicator turns on to show that the filter  
needs to be cleaned.  
5.7 Starting the program  
Start the program by pressing the Start/Pause button.  
Indicators of Start/Pause/Ready and Drying turn on to  
show that program has started.  
Water tank  
The warning indicator turns on to show that the water  
tank needs to be drained.  
If the water tank fills during the operation of program,  
warning indicator flashes and machine pauses. In  
such a case, drain the water in water tank and start  
the program by pressing Start/Pause button. Warning  
indicator turns off and program is resumed.  
5.8 Child Lock  
There is a child lock in the tumble drier that prevents the  
program flow from being affected when the buttons are  
pressed during operation of program. When the Child  
Lock is active, all buttons on the panel are disabled  
except for the On/off/program selection button.  
In order to activate the child lock, press and hold the  
Delay time and Audio alarm buttons spontaneously for  
3 seconds.  
Delay time  
If you prefer to dry your laundry after a certain period of  
time, you may delay the start of program up to 3, 6 or 9  
hours thanks to the delay function.  
Once the program is completed, the child lock must  
be disabled to start a new program or intervene in  
the program. Press and hold the same buttons for 3  
seconds to disable the child lock.  
Open the loading door, and put the laundry in.  
Select the drying program.  
By pressing the Delay time selection button, set  
the desired delay time. When the Delay time button  
is pressed one more time, 3-hour delay is selected  
and relevant indicator light turns on. When the  
same button is pressed again, 6-hour delay is  
selected, and one more pressing causes 9-hour  
delay. If the delay time button is pressed once  
more, the delay is cancelled.  
When the Child Lock is enabled, child  
lock warning indicator on the display  
turns on.  
C
Child lock is disabled when the tumble  
drier is turned off and turned on again  
C
by using the On/off/program selection  
After the selection of Delay time, delayed operation  
is started for the selected program by pressing  
“Start/Pause” button.  
button.  
Child lock is disabled when the machine  
is turned off and turned on again by using  
C
the On/off/program selection button.  
When the child lock is active:  
If the position of program selection button is changed  
while the tumble drier is running or paused, indicator  
symbols do not change.  
 
Dryer / User Manual  
20 / 28 EN  
Operating the product  
5.10 Cancelling the program  
When the program selection switch is  
turned while the tumble drier is running  
and child lock is active, two beeps are  
heard. If the child lock is cancelled  
without restoring the program selection  
to switch to its previous position, program  
is ended because the position of program  
selection switch is changed.  
When you want to cancel the program and end the  
drying process for any reason after the tumble drier has  
started operation, the program is cancelled by turning  
the On/off/program selection button.  
C
WARNING: When you cancel the  
program during the operation of tumble  
A drier, inner part will be extremely hot;  
therefore, allow it to cool down by running  
the airing program.  
5.9 Changing the program after  
starting  
After the tumble drier starts running, you may dry your  
laundry in a different program by changing the selected  
program.  
5.11 End of program  
At the end of program, Fibre Filter Cleaning and Water  
Tank warning symbols on the program monitoring  
indicator turn on. Loading door can be opened, and the  
tumble drier will be ready for a second operation.  
In order to turn off the tumble drier, put the On/Off/  
Program selection button in On/Off position.  
For instance, in order to select Extra Dry instead  
of Iron Dryness program, select the Extra Dry  
program by turning the On/off/program selection  
button.  
Start the p rogram by pressing the Start/Pause button.  
Adding or removing laundry during pause  
If you want to add or remove laundry after the drying  
program has started:  
When the laundry isn’t removed after the  
end of program, 2-hour anti-creasing  
Put the tumble drier into Pause position by  
pressing the Start/Pause button. Drying process  
stops.  
Open the loading door in Pause position, and close  
the door after adding or removing laundry.  
Start the program by pressing the Start/Pause  
button.  
C
function is enabled in order to prevent  
creasing of laundry. Program spins the  
laundry at intervals of 10 minutes, and  
prevents creasing.  
Clean the fibre filter after each drying.  
(See: “Fibre filter and Loading door inner  
C
C
surface”)  
The process of adding laundry after  
the start of drying process might lead  
to mixing of wet laundry with the dried  
laundry inside the tumble drier and some  
damp laundry at the end of process.  
Drain the water tank after each drying.  
(See: “Draining the water tank”)  
C
Laundry adding and removing process  
can be repeated as many times as  
C
desired during drying. But this process  
leads to extension in the program time  
and increase in energy consumption  
since it will repeatedly interrupt the during  
process. Therefore, it is recommended to  
add laundry before starting the program.  
If a new program is selected by changing  
the position of program selection button  
while the tumble drier is paused, the  
running program ends.  
C
Do not contact the inner surface of drum  
while adding or removing laundry during a  
running program. Surface of drum is hot.  
 
Dryer / User Manual  
21 / 28 EN  
6 Maintenance and cleaning  
Service life of product extends and frequently  
experienced problems will be reduced if it is cleaned at  
regular intervals.  
6.1 Cleaning Lint Filter / Loading Door  
Inner Surface  
Lint and fiber released from the laundry to the air during  
the drying cycle are collected in the Lint Filter.  
Clean the entire inner surface of the loading door  
and loading door gasket with a soft damp cloth.  
Such fiber and lint are generally formed  
during wearing and washing.  
C
A
Always clean the lint filter and the inner  
surfaces of the loading door after each  
drying process.  
You can clean the lint filter housing with a  
vacuum cleaner.  
C
To clean the lint filter:  
Open the loading door.  
Remove the lint filter by pulling it up and open the  
lint filter.  
Clean lint, fiber, and cotton raveling by hand or with  
a soft piece of cloth.  
Close the lint filter and place it back into its  
housing.  
6.2 Cleaning the sensor  
There are dampness sensors in the dryer that detect  
whether the laundry is dry or not.  
To clean the sensors:  
Open the loading doorof the dryer.  
Allow the machine to cool down if it is still hot due  
to the drying process.  
Wipe the metal surfaces of the sensor with a soft  
cloth, dampened with vinegar and dry them.  
A layer can build up on the filter pores that can  
cause clogging of the filter after using the dryer  
for a while. Wash the lint filter with warm water  
to remove the layer that builds up on the lint  
filter surface. Dry the lint filter completely before  
reinstalling it.  
Clean metal surfaces of the sensors 4  
times a year.  
C
C
Do not use metal tools when cleaning  
metal surfaces of the sensors.  
 
Dryer / User Manual  
22 / 28 EN  
Maintenance and cleaning  
Drain the water in the tank.  
Never use solvents, cleaning agents or  
similar substances for cleaning due to the  
risk of fire and explosion!  
A
If there is lint accumulation in the funnel of the  
water tank, clean it under running water.  
Place the water tank into its seat.  
If the direct water draining is used as  
an option, there is no need to empty the  
C
water tank.  
6.3 Draining the water tank  
Dampness of the laundry is removed and condensed  
during drying process and the water that arise  
accumulates in the water tank. Drain the water tank  
after each drying cycle.  
6.4 Cleaning the condenser;  
Hot and humid air in the condenser is cooled with the  
cold air from the room. Thus, the humid air circulating in  
your dryer is condensed and then pumped into the tank.  
Clean the condenser after every 30 drying  
Condensed water is not drinkable!  
cycles or once a month.  
C
A
Never remove the water tank when the  
program is running!  
To clean the condenser:  
1. If a drying process has been carried out, open the  
door of the machine and wait until it cools down.  
A
If you forget to drain the water tank, the machine will  
stop during the subsequent drying cycles when the  
water tank is full and the Water Tank warning symbol  
will flash. If this is the case, drain the water tank and  
press Start / Pause button to resume the drying cycle.  
To drain the water tank:  
Pull the drawer and remove the water tank carefully.  
 
Dryer / User Manual  
23 / 28 EN  
Maintenance and cleaning  
2. Unlock the 2 condenser locks after opening the kick  
plate.  
6. Close the kick plate cover.  
3. Pull out the condenser.  
4. Clean the condenser by applying pressurized water  
with a shower armature and wait until the water  
drains.  
5. Place the condenser in its housing. Fasten the 2 locks  
and make sure that they are seated securely.  
 
Dryer / User Manual  
24 / 28 EN  
7 Troubleshooting  
Drying process lasts for a long time.  
Pores of the fibre filter might be clogged. >>> Wash the filter with warm water.  
Condenser might be clogged. >>> Wash the condenser.  
Ventilation grills at the front of machine might be blocked. >>> Remove any items in front of the ventilation  
grills that block ventilation.  
Ventilation might be inadequate if the installation area is very small. >>> Open the windows and doors in  
order to prevent excessive increase in room temperature.  
There might be furring on the damp sensor. >>> Clean the damp sensor.  
Laundry might be overloaded. >>> Do not overload the tumble drier.  
Laundry might not have been adequately spun. >>> Increase the rpm of tumble drier.  
Laundry is still wet at the end of drying.  
Hot laundry unloaded at the end of drying feel wetter than they really are.  
C
You may not have used a program suitable for laundry type.>>> Check the maintenance labels on the  
laundry and select a program suitable for their type, or use the time programs additionally.  
Pores of the fibre filter might be clogged. >>> Wash the filter with warm water.  
Condenser might be clogged. >>> Wash the condenser.  
Laundry might be overloaded. >>> Do not overload the tumble drier.  
Laundry might not have been adequately spun. >>> Increase the rpm of tumble drier.  
Tumble drier does not turn on or program cannot be started. Tumble drier does not activate when set.  
The power cord might not be plugged in. >>> Make sure the power cord is plugged in.  
Loading door might be open. >>> Make sure that the loading door is properly closed.  
You may not have set the program or pressed the Start/Pause button. >>> Make sure that you have set the  
program and it is not in Pause position.  
Child lock might be active. >>> Disable the child lock.  
Program was interrupted for no reason.  
Loading door might not be properly closed. >>> Make sure that the loading door is properly closed.  
A power cut might have occurred. >>> Press the Start/ Pause button to start the program.  
Water tank might be full. >>> Drain the water tank.  
Laundry is shrunk, felt or worn out.  
You may not have used a program suitable for laundry type. >>> Check the maintenance labels on the  
laundry and select a program suitable for their type.  
The lighting inside the tumble drier does not turn on. (In models with lamps)  
You may not have turned on the tumble drier be using On/Off/Cancel button. >>> Make sure that the tumble  
drier is at ‘on’ position.  
Lamp might be broken. >>> Contact the Authorized Service for the replacement of lamp.  
Filter cleaning warning led is on.  
Fibre filter might not have been cleaned. >>> Clean the filter.  
Filter cleaning warning led flashes.  
Filter bearing might be clogged with fibre. >>> Clean the filter bearing.  
There might be a layer in the filter pores that causes clogging. >>> Wash the filter with warm water.  
Condenser might be clogged. >>> Wash the condenser.  
 
Dryer / User Manual  
25 / 28 EN  
Troubleshooting  
Water is leaking from the condenser cover.  
There might be fibre build-up inside the loading door and on the surfaces of loading door gasket. >>> Clean  
the inner surfaces of loading door and surfaces of loading door gasket.  
Loading door opens itself.  
Loading door might not be properly closed. >>> Push the loading door until you hear the closing sound.  
Water tank warning led is on/flashes.  
Water tank might be full. >>> Drain the water tank.  
Water drain hose might be folded. >>> Check the water drain hose if the product is directly connected to the  
water outlet.  
If you cannot eliminate the problem despite following these instructions, please contact the vendor that  
.sold you the product or an Authorized Service. Do not try to repair the product yourself  
A
 
Dryer / User Manual  
26 / 28 EN  
8 Electrical Connection  
Make sure that you have an earthed power outlet  
socket rated at 13 amps (minimum).  
Important  
Fitting a different plug  
A
As the colours of the wires in the mains lead  
of this appliance may not correspond with the  
coloured markings identifying the terminals on  
your plug, proceed as follows:  
1 Connect the green - yellow or green (earth) wire  
to the terminal in the plug marked ‘E’ or with the  
symbol or coloured green and yellow or green.  
2 Connect the blue (neutral) wire to the terminal in  
the plug marked ‘N’ or coloured black.  
Attention!  
If you use your dryer as built-in, the socket must  
be reachable after installation, or a separate  
switch (which can disconnect the two poles) must  
be used in the installation. Check for suitability.  
For a permanent connection, a master switch with  
at least 3mm contact clearance and minumum 13  
A rating must be used.  
Electrical requirements  
3 Connect the brown (live) wire to the terminal in  
the plug marked ‘Lor coloured red.  
Before you insert the plug into the wall socket  
make sure that the voltage and the frequency  
shown in the rating label corresponds to your  
electricity supply.  
With the alternative plugs a 13A fuse must be  
fitted either in the plug or adaptor or in the main  
fuse box. If in doubt contact a qualified electrician.  
We recommend that this appliance be connected  
to the mains supply via a suitable switched and  
fused socket in a readily accessible position.  
Should the mains lead of the appliance become  
damaged or need replacing at any time, it must  
be replaced by a special purpose made mains  
lead which can only be obtained from a Authorised  
Service Agent.  
Green and yellow  
or green  
A Warning  
This appliance must be earthed  
N
L
Blue or black  
Brown or red  
If the fitted moulded plug is not suitable for your  
socket, then the plug should be cut off and an  
appropriate plug fitted.  
The moulded plug on this appliance incorporates a  
13A fuse. Should the fuse need to be replaced an  
ASTA approved BS1362 fuse of the same rating  
must be used. Do not forget to refit the fuse cover.  
In the event of losing the fuse cover, the plug must  
not be used until a replacement fuse cover has  
been fitted. Colour of the replacement fuse cover  
must be the same colour as that visible on the pin  
face of the plug. Fuse covers are available from  
any good electrical store.  
In order to avoid hazards, damaged supply cord  
should be replaced by the manufacturer, its service  
agent or similarly qualified people.  
 
Dryer / User Manual  
27 / 28 EN  
 

ADTRAN Network Card ISDN Terminal Adapter User Manual
AEG Washer Dryer 16850 User Manual
Aiwa Universal Remote MF 355RF User Manual
Alto Shaam Oven 1200 S Series User Manual
Amana Range ZRRSC8050 User Manual
American Standard Hot Tub 0153015 User Manual
Audiovox Car Stereo System ACC 60 User Manual
Audiovox Remote Starter AA RS20CS User Manual
Ayre Acoustics Stereo Amplifier AX 7E User Manual
Barco Camera Lens R9849853 User Manual