Extron electronic Power Supply PS 1210 User Manual

2. Fasten the power output cord to the ZipClip base.  
Extron External Power Supply •  
a. Insert tie wraps (“zip ties”) along the notches on the side of the  
Installation Guide  
power supply and  
through the tie wrap  
anchor points on the  
ZipClip, then around  
the cord.  
Important Safety Instructions  
This symbol is intended to alert the user of impor-  
tant operating and maintenance (servicing) instruc-  
tions in the literature provided with the equipment.  
WARNING: To reduce the risk of fire or electric shock, do not  
expose this apparatus to rain or moisture.  
This apparatus shall not be exposed to dripping or splashing  
and no objects filled with liquids, such as vases shall be  
placed on the apparatus.  
Cable  
Strain  
Relief  
b. Connect and pull the  
This symbol is intended to alert the user of the  
presence of uninsulated dangerous voltage within  
the product enclosure that may present a risk of  
electric shock. On the product, risk of shock may  
be indicated by this symbol.  
tie wraps until they  
Tie Wrap  
Refer all servicing to qualified service personnel. Servicing is required  
when the apparatus has been damaged in any way, such as  
when the power-supply cord or plug is damaged, liquid has  
been spilled or objects have fallen into the apparatus, the  
apparatus has been exposed to rain or moisture, does not  
operate normally, or has been dropped.  
are secure. Do not  
over tighten.  
Read these instructions.  
Keep these instructions.  
Heed all warnings.  
Follow all instructions.  
Mounting  
WARNING: This apparatus is a Class I product. This product  
must be connected to a MAINS socket outlet with a  
protective earthing connection.  
Do not use this apparatus near water.  
Clean only with dry cloth.  
Do not block any ventilation openings. Install in accordance with the  
manufacturer’s instructions.  
CAUTION: These power supplies are not suitable for use in air handling  
spaces or in wall cavities. The power supply is to be located within  
the vicinity of the Extron AV equipment in an ordinary location  
with IEC 1010 pollution degree 2, and secured to an equipment rack  
within a dedicated closet, podium, or desk.  
The mains plug is used as the disconnect device and shall remain  
readily operable.  
Do not install near any heat sources such as radiators, heat registers,  
stoves, or other apparatus (including amplifiers) that produce heat.  
To prevent the risk of shock, do not attempt to service this  
equipment yourself because opening or removing covers may  
expose you to dangerous voltage or other hazards.  
Do not defeat the safety purpose of the polarized or grounding-type  
plug. A polarized plug has two blades with one wider than  
the other. A grounding type plug has two blades and a third  
grounding prong. The wide blade or the third prong are provided  
for your safety. If the provided plug does not fit into your outlet,  
consult an electrician for replacement of the obsolete outlet.  
WARNING:  
Power sources • This equipment should be operated only from  
the power source indicated on the product. This equipment  
is intended to be used with a main power system with a  
grounded (neutral) conductor. The third (grounding) pin is  
a safety feature, do not attempt to bypass or disable it.  
The installation must be in accordance with the applicable provisions  
of National Electrical Code ANSI/NFPA 70, article 75 and Canadian  
Electrical Code part 1, section 16. The power supply shall not be  
permanently fixed to building or similar structure.  
Protect the power cord from being walked on or pinched particularly at  
plugs, convenience receptacles, and the point where they exit from  
the apparatus.  
Only use attachments/accessories specified by the manufacturer.  
Power disconnection • To remove power from the equipment  
safely, remove all power cords from the rear of the  
equipment, or the desktop power module (if detachable), or  
from the power source receptacle (wall plug).  
Unplug this device apparatus during lightning storms or when  
unused for long periods of time.  
Rack Mounting  
Mounting to a Rack Shelf  
About the Extron PS 910, PS 1210, PS 1508  
Power Supplies  
These power supplies are one eighth rack wide. Up to eight power supplies  
can be mounted side by side directly onto a rack shelf.  
1. Align the threaded holes in the bottom of the power supply with the  
Model Overview  
holes in an Extron rack  
shelf and fasten the  
supply to the shelf  
with two 4-40 x 3/16"  
screws as shown  
below.  
Model  
Power Output  
9 watts, 9 VDC, 1 A  
9 watts, 9 VDC, 1 A  
12 watts, 12 VDC, 1 A  
12 watts, 12 VDC, 1 A  
12 watts, 15 VDC, 0.8 A  
Termination  
Captive screw  
DC plug  
PS 910C  
PS 910P  
PS 1210C  
PS 1210P  
PS 1508C  
Captive screw  
DC plug  
Captive screw  
ZipClip100  
b
(101-002-01)  
RSB 123  
Rack Shelf  
Cabling and Features  
Features  
a
(2) 4-40 x 3/16"  
Screws  
Notches for  
Securing  
Tie Wrap  
AC  
Power  
Input  
2. Bolt the rack shelf to the rack.  
Power  
LED  
z
X
1MA  
124V5-60H  
Mounting to Rack Rails Using a ZipClip  
ZipClip  
Mounting Slot  
(front and rear)  
1. Fasten the ZipClip 100  
mounting clip to a  
rack rail using  
two rack  
DC Power  
Output  
Connector Pin Assignments  
screws as  
shown in the  
PS 910C, PS 1210C, PS 1508C  
PS 910P, PS 1210P  
Tie Wrap  
Smooth  
diagram at  
ZipClip 100  
right.  
Tip (+)  
Power Supply  
Output Cord  
Captive Screw  
Connector  
Ridged  
Sleeve (  
-)  
Side of Rack  
Alternative Wiring Option  
Smooth  
2. Insert the  
power supply  
into the ZipClip as  
described previously  
and press to snap it  
into place.  
Power Supply  
N/C  
Back of  
Rack  
Output Cord  
Ridged  
Inside  
Rack  
Using the ZipClip 100  
Attaching and Removing the Clip and Power Supply  
To attach the power supply to the ZipClip 100 mounting clip:  
Pole or Table Leg Mounting  
1. Insert the bottom of the power supply down into the clip,  
starting with one end.  
1. Wrap a tie wrap around  
the projector mount pole or table  
leg and the power supply at one of  
the tie wrap notches, and fasten the  
2. Pivot the other end down and press until the clip snaps into place.  
tie wrap together to secure the  
power supply to the pole or table  
leg.  
To remove the power supply from the ZipClip:  
Tie Wrap  
to Pole  
b
1. Press the tab on the ZipClip.  
2. Pivot the power supply and lift it out  
2. Repeat step 1 at the other tie wrap  
of the ZipClip.  
notch.  
a
Using Tie Wraps for Cable Strain Relief  
1. Attach the power supply to the ZipClip mounting clip as described  
See the next page for  
furniture mounting instructions.  
previously.  
1
 

Flowtron Outdoor Products Insect Control Equipment MT 200 Series User Manual
GE Clothes Dryer DBB5500 User Manual
GE Double Oven EER2000 User Manual
GE Freezer FCM9SAWH User Manual
GE Home Security System 60 639 43 EUR User Manual
GE Monogram Double Oven ZEK958SM BM User Manual
GE Ventilation Hood BF50 User Manual
Glowworm Lighting Water Heater 200 I User Manual
Golden Technologies Mobility Aid GP52 User Manual
Go Video DVR VR2945 User Manual